Lateral Compression Process of Bimetallic Rods between Flat and V-shaped Dies: Experimental Analysis and Numerical Simulation
الموضوعات :Mahtab Safaee 1 , Heshmatollah Haghighat 2
1 - MSc Student, Mechanical Engineering Department, Razi University, Kermanshah, Iran
2 - Associate Professor, Mechanical Engineering Department, Razi University, Kermanshah, Iran
الکلمات المفتاحية: Lateral Compression, Bimetallic Rod, Forming Force, Experiment, FE Simulation,
ملخص المقالة :
This study deals with the experimental and numerical investigation of the lateral compression process of bimetallic rods between flat and V-shaped dies. The bimetallic rods are long and have a round cross-section and are made of a combination of 1050 series aluminum metal as a shell and Cu-ETP R250 copper metal as a core. To determine the stress behavior in terms of the strain of these two materials, tensile test samples were made with standard dimensions, and by performing a simple tensile test, the true stress curve was drawn in terms of the true strain. To make bimetallic rods, aluminum rods and copper tubes with equal lengths were made separately. Then, the copper tube is heated in oil, and the aluminum rod is assembled inside the copper tube by applying force. The bimetallic rod is placed horizontally on the lower V-shaped die, which is fixed, and is subjected to plastic deformation by the upper flat die, which is connected to the moving part of the press machine at ambient temperature by applying compressive force. The lateral compression process was simulated by the finite element method using ABAQUS software. The geometric dimensions of the deformed bimetallic rod cross-section and the experimental forming force have been compared with the FE simulation results. The comparisons showed good agreement between the experimental and FE simulation results.
[1] Abbasi, M., Taheri, A.K. and Salehi, M.T. 2001. Growth rate of intermetallic compounds in Al/Cu bimetal produced by cold roll welding process. Journal of Alloys and Compounds. 319:233-241. doi: 10.1016/S0925-8388(01)00872-6.
[2] Lee, J.E., Bae, D.H., Chung, W.S., Kim, K.H., Lee, J.H. and Cho, Y.R. 2007. Effects of annealing on the mechanical and interface properties of stainless steel/aluminum/copper clad-metal sheet. Journal of Materials Processing Technology. 187:546-549. doi:10.1016/j.jmatprotec.2006.11.121.
[3] Ko, D.C., Lee, S.K., Kim, B.M., Jo, H.H. and Jo. H. 2007. Evaluation of copper coating ratio in steel/copper clad wire drawing, Journal of Materials Processing Technology. 186:22-26. doi: 10.1016/j.jmatprotec.2006.11.131.
[4] Tokuno H. and Ikeda K. 1991. Analysis of deformation in extrusion of composite rods. Journal of Materials Processing Technology. 26:323–335. doi: 10.1016/0924-0136(91)90067-O.
[5] Hwang Y. and Hwang T. 2002. An investigation into the plastic deformation behavior within a conical die during composite rod extrusion. Journal of Materials Processing Technology. 121:226–233. doi: 10.1016/j.apm.2019.08.020.
[6] Kazanowski, P., Epler, M.E. and Misiolek, W.Z. 2004. Bi-metal rod extrusion process and product optimization. Materials Science and Engineering: A. 369:170-180. doi: 10.1016 /j.msea.2003.11.002.
[7] Danishevs’kyy, V.V., Guillet, A., Pareige, P. and Weichert, D. 2008. An analytical approach to the plastic flow of a bimetallic mono-filamentary wire through a conical die. Mechanics of Materials. 40:284–292. doi: 10.1016/j.mechmat.2007.08.001.
[8] Khosravifard, A. and Ebrahimi, R. 2010. Investigation of parameters affecting interface strength in Al/Cu clad bimetal rod extrusion process. Materials and Design. 31:493-499. doi: 10.1016/j.matdes.2009.06.026.
[9] Dudra, S.P. and Im, Y.T. 1990. Investigation of metal flow in open-die forging with different die and billet geometries. Journal of Materials Processing Technology. 21:143-154. doi: 10.1016/0924-0136(90)90003-D.
[10] Christiansen P., Hattel J.H., Kotas P. and Laszlo V. 2012. Modelling the void deformation and closure by hot forging of ingot castings. 1st International Conference on Ingot Casting, Rolling and Forging Technology.
[11] Ayer, O. 2016. Material flow analysis of bimetallic hollow disc upsetting. 6th International Conference on Trends in Agricultural Engineering. Prague. Czech Republic.
[12] Essa, K., Kacmarcik, I., Hartley, P., Plancak, M. and Vilotic D. 2012. Upsetting of bi-metallic ring billets. Journal of Materials Processing Technology. 4:817-824. doi: 10.1016 /j.jmatprotec.2011.11.005.
[13] Jin, K., Yuan, Q., Tao, J., Domblesky, J. and Guo, X. 2019. Analysis of the forming characteristics for Cu/Al bimetal tubes produced by the spinning process. International Journal of Advanced Manufacturing Technology. 101:147–155. doi: 10.1007/s00170-018-2836-6.
[14] Rajhi, W., Ayadi, B., Khaliq, A., Al-Ghamdi, A., Ramadan, M., Al-shammrei, S., Boulila, A., and Aichouni, M. 2021. Constitutive behavior and fracture of intermetallic compound layer in bimetallic composite materials: Modeling and application to bimetal forming process. Materials & Design. 212:110294. doi: 10.1016/j.matdes.2021.110294.
[15] Parvizi Bina E. and Haghighat, H. 2021. Limit analysis of plane strain compression of cylindrical billets between flat dies. The International Journal of Advanced Manufacturing Technology. 116:3561–3570. doi: 10.1007/s00170-021-07711-1.
[16] Maleki, M. and Haghighat, H. 2022. The modelling of the mechanics of deformation in plane strain upsetting of round cross-section billets between the flat and V-shaped dies. Journal of Solid Mechanics. 14:468-476. doi: 10.22034/jsm.2021.1929196.1693.
[17] Qian, L., Cui, Z., Sun, C., Geng, S. and Sun, Z. 2022. Investigation of deformation compatibility and power consumption during KOBO extrusion of bimetallic composite tube. International Journal of Advanced Manufacturing Technology. 118:3477–3486. doi: 10.1007/s00170-021-08608-9.
[18] Kazemi, H. and Haghighat, H. 2023. Experimental and Numerical Analysis of Local Lateral Compression Process of Metal Tubes between Cylindrical Shaped Dies. Journal of Modern Processes in Manufacturing and Production. 12:57-70. doi: 10.71762/mpmp.2023. 996934.
[19] Tang, Y. 2024. Research on the forming process of bimetal composite pipe by hydroforming. SAE Technical Paper 2024-01-5001. doi: 10.4271/2024-01-5001.
