Influence of Steel Slag Aggregate Gradation on the Improvement of Concrete Properties

الموضوعات :

Hossein Abbastabar Ahangar ¹ , Seyed Esmaeil Mohammadyan-Yasouj ² , Leyla Adelzade Saadabadi ³ , Navid Arshadi ⁴ , Mohammadreza Javid Rad ⁵

1 - Department of Chemistry, Najafabad Branch, Islamic Azad University, Najafabad, Iran.
2 - Department of Civil Engineering, Najafabad Branch, Islamic Azad University, Najafabad, Iran.
3 - Department of Civil Engineering, Najafabad Branch, Islamic Azad University, Najafabad, Iran.
4 - Department of Civil Engineering, Najafabad Branch, Islamic Azad University, Najafabad, Iran.
5 - Department of Civil Engineering, Najafabad Branch, Islamic Azad University, Najafabad, Iran.

تاريخ الإرسال : 03 الثلاثاء , محرم, 1446 تاريخ التأكيد : 04 الإثنين , ربيع الثاني, 1446 تاريخ الإصدار : 11 الإثنين , شوال, 1444

الکلمات المفتاحية: Steel Slag, Concrete, Aggregate Replacement, Compressive Strength,

ملخص المقالة :

Steel slag, as a by-product of the iron industry, is widely produced in the world. In this paper, steel slag from local furnaces is partially replaced as concrete aggregate to compensate for irregular consumption of raw material for concrete and reduce environmental impacts of waste slag. Six mix designs were considered, and three categories of aggregate size were selected to evaluate the aggregate replacement effect in the concrete samples. Sieve analysis, X-ray diffraction (XRD) analysis, aggregate porosity, slump, compressive strength, and microstructure analysis were implemented to investigate aggregates and concrete samples. The results showed that compressive strength and water absorption of the concrete with 20% aggregate replacement were 37.4 MPa and 3%. By 20% aggregate replacement, improvement in the compressive strength and reduction in the water absorption were observed. Increasing aggregate replacement to 40% reduced compressive strength by 62% and increased water absorption. In the concrete containing 62% of the replacement, the required compressive strength of 30 MPa, as design compressive strength, was achieved. However, although the pores in the slag aggregates can affect fresh and hardened properties of concrete, selecting an appropriate range of aggregates from the gradation curve can limit the side effects due to the pores.

المصادر:

1. R. Zhengyi, L. Dongsheng, Application of Steel Slag as an Aggregate in Concrete Production: A Review. Materials, 16 (2023) 5841.
2. J. Guo, Y. Bao, M. Wang, Steel slag in China: Treatment, recycling, and management. Waste Manag, 78 (2018) 318.
3. O. Najm, H. El-Hassan, A. El-Dieb, Ladle slag characteristics and use in mortar and concrete: A comprehensive review. J. Clean. Prod, 288 (2020) 125584.
4. L. Zhennan, S. Aiqin, Y. Xuerui, G. Yinchuan, L. Yiwei, A review of steel slag as a substitute for natural aggregate applied to cement concrete. Road Materials and Pavement Design, 24 (2023) 537.
5. N. Alberto, C. Jean-Pierre Birat, A. Dutta, A review of the current environmental challenges of the steel industry and its value chain. Journal of Environmental Management, 259 (2020) 109782.
6. S. Adeyemi Alabi, J. Mahachi, Performance of concrete made from cupola furnace slag and recycled concrete aggregate. Materials Today: Proceedings, 62 (2022) S110.
7. A. Nageib, M. A. Khafaga , W. S. Fahmy, Mohamed Amen Sherif and Asmaa Mohamed Nageib Abdel Hamid. Properties of high strength concrete containing electric arc furnace steel slag aggregate. Journal of Engineering Sciences Assiut University Faculty of Engineering, 42 (2014) 582.
8. A. Pribulova, P. Futas, J. Petrik, M. Pokusova, M. Brzinski, J. Jakubski, Comparison of cupola furnace and blast furnace slags with respect to possibilities of their utilization. Arch. Metall. Mater. 63 (2018) 1865.
9. J. Liu, R. Guo, Applications of Steel Slag Powder and Steel Slag Aggregate in Ultra-High Performance Concrete. Advances in Civil Engineering, (2018) 1426037.
10. I. Sosa, C. Thomas, J. Antonio Polanco, J. Setién, P. Tamayo, High Performance Self-Compacting Concrete with Electric Arc Furnace Slag Aggregate and Cupola Slag Powder. Appl. Sci. 10 (2020) 773.
11. P. Kumar, S. Kumar Soni, Comparative study on the effects of steel slag aggregate over blended Cement concrete. https://doi.org/10.22214/ijraset.2022.42893.
12. M. A. Khafaga, W. S. Fahmy, M. A. Sherif, A. M. Nageib Abdel Hamid, Effect of using locally produced electic ARC furnace steel slag in Egypt as aggregate in normal, high and ultra-high strength concrete exposed to elevated temperature. 1st International Conference on Innovative Building Materials Dec. (2014) 28.
13. A. Vishavkarma, H. Kizhakkumodom Venkatanarayanan, Assessment of pore structure of foam concrete containing slag for improved durability performance in reinforced concrete applications. Journal of Building Engineering, 86 (2024) 108939.
14. V.S. Devi, B. Gnanavel, Properties of concrete manufactured using steel slag. Procedia Engineering 97(12) 95.
15. L.H.Viet, H.L. Do, K.D. Joo, Effects of steel slag aggregate size and content on piezoresistive responses of smart ultra-high-performance fiber-reinforced concretes. Sensors Actuators A: Physical, 807 (2020) 111925.
16. ASTM C 150- 07, “Standard Specification for Portland Cement,” Annual Book of ASTM Standards, pp. 1–8, 2007.
17. https://en.isfahancement.com/product/portland-cement-type-1-425/
18. ASTM C136-06 ,"Standard Test Method for Sieve Analysis of Fine and Coarse Aggregates",Annual Book of ASTM Standards, Feb, pp. 1–5, 2006.
19. ASTM C 217, “Standard Test Method for Density, Relative Density (Specific Gravity), and Absorption of Coarse Aggregate,” Annual Book of ASTM Standards, pp.1-6, Aug. 1, 2007.
20. ASTM C 218, “Standard Test Method for Density, Relative Density (Specific Gravity), and Absorption of Fine Aggregate,” Annual Book of ASTM Standards, pp.1-6, Aug. 1, 2007.
21. ASTM-C131, "Standard Test Method for Resistance to Degradation of Small-Size Coarse Aggregate by Abrasion and Impact in the Los Angeles Machine", Aug. 1, 2003.
22. INSO-448, “Aggregates- Resistance to Degradation of Small-Size Coarse Aggregateby Abrasion and Impact in the LosAngeles Machine- Test Method", 2015
23. A. Amani, A. M. Ramezanianpour, M. Palassi, Investigation on the sustainable use of electric arc furnace slag aggregates in eco-friendly alkali-activated low fineness slag concrete as a green construction composite. Journal of Cleaner Production, 307 (2021) 127257.
24. Q. Dong, G. W. Xueqin Chen, J. Tan, X. Gu, Recycling of steel slag aggregate in portland cement concrete : An overview", Journal of Cleaner Production, 272 (2021) 124447.
25. R. K. Patra, B. B. Mukharje, Influence of incorporation of granulated blast furnace slag as replacement of fine aggregate on properties of concrete. Journal of Cleaner Production, 165 (2017) 468-476.
26. N. Palankar, A.U. Ravi Shankar, B.M. Mithun, Durability studies on eco-friendly concrete mixes incorporating steel slag as coarse aggregates. Journal of Cleaner Production, 129 (2016) 437-448.
27. ACI 211.1-91, “Standard Practice for Selecting Proportions for Normal, Heavyweight, and Mass Concrete",1991.
28. M. Herbelin, J. Bascou, V. Lavastre, D. Guillaume, M. Benbakkar, et al., Steel Slag Characterisation-Benefit of Coupling Chemical, Mineralogical and Magnetic Techniques. Minerals, 10 (2020).705.
29. M. C. Llanes, M. R. Pérez, M. J. G. González, J. P. Bolívar Raya, Construction and demolition waste as recycled aggregate for environmentally friendly concrete paving. Environmental Science and Pollution Research, 29 (2022) 9826.
30. H. Liu, T. Liu, Z. Yin, X. Liu, Y. Tan, Y. Zhao, H. Yu, Bio-functional hydroxyapatite-coated 3D porous polyetherketoneketone scaffold for enhanced osteogenesis and osteointegration in orthopedic applications. Regenerative Biomaterials, 11 (2024) 11.