An Investigation on the Metal Injection through the Producing of MIM-ed Low-Alloy Steel
الموضوعات : Journal of Environmental Friendly Materials
1 - Department of Materials Engineering, Science and Research Branch, Islamic Azad University, Tehran, Iran.
2 - Department of Mechanical Engineering, Nazarabad Centre, Karaj Branch, Islamic Azad University, Karaj, Iran.
الکلمات المفتاحية: Metal Injection Molding, Low Alloy Steel 4605, Feedstock, Density, Response Surface Methodology.,
ملخص المقالة :
In this study, we demonstrate the injection stage of Metal Injection Molding (MIM) process to fabricate a small bend-type component. This non-standard but critical engine part is made of a feedstock from the low alloy steel 4605. To optimize various injection parameters, the five-variable Box-Behnken Design (BBD) is used with the assumption of a quadratic model, together with the statistical method of Response Surface Methodology (RSM). Samples are then fabricated, and their densities are measured. Hence, the significance of these factors as well as the mutual coupling between each two parameters are investigated using the analysis of variance (ANOVA). Finally, this paper reveals that injection temperature of 155 ◦C, the injection speed of 80 mm/s, holding pressure of 83 bar, holding time of 9 s and the injection pressure of 132 bar led to an optimum density of the green part, which becomes 4.892 g/cm3. Then, a new sample is produced using these optimized settings, and the green component density is measured, which is extremely near to the predicted value. After sintering, the optimized sample’s density and hardness are compared to the MIM-4605 standard criteria.
[1] Husein, S., Park, J.H., Choi, D.Y. and Ko, Y.G., Influence of sintering temperature on microstructure and mechanical properties of Fe–2Ni–2Cu alloy processed by metal injection moulding. Mater. Res. Innov. 2014; 18(sup2):S2-633.
[2] Huang, C., Li, L., Ngai, T., Zhang, W. and Ngai, S., November. Effect of sintering temperature and solution treatment on microstructure and mechanical properties of high-N Ni-free austenitic stainless steel prepared by metal injection molding. Mater. Res. Express. IOP Publishing. 2020; 1676(1):012099
[3] Berginc, B., Kampus, Z., Sustarsic, B. The use of the TAGUCHI approach to determine the influence of injection-moulding parameters on the properties of green parts. J. Achieve. Mater. Manuf. Eng. 2006;15(1-2):63–70.
[4] Chua, M.I.H., Sulong, A.B, Abdullah, M.F., et al. Optimization of injection molding and solvent debinding parameters of stainless-steel powder (ss316l) based feedstock for metal injection molding. Sains Malays. 2013; 42(12):1743–50.
[5] Arifin, A., Sulong, A.B., Muhamad, N. Optimizing injection parameter of metal injection molding processes using the feedstock of 16 µm stainless steel powder (ss316l), peg, pmma and stearic acid. J. Appl. Sci. Res. 2012; 8(6):2998-3003
[6] Jamaludin KR, Muhamad N, Rahman MA, Amin SY, Ahmad S, Ibrahim MH. Sintering parameter optimisation of the SS316L metal injection molding (MIM) compacts for final density using taguchi method. InUniv Consort Symp 2009 pp. 258-62.
[7] Virdhian S, Osada T, Kang HG, Tsumori F, Miura H. Evaluation and analysis of distortion of complex shaped Ti-6Al-4V compacts by metal injection molding process. Key Eng. Mater. 2012, 19;520:187-94.
[8] Thomas-Vielma P, Cervera A, Levenfeld B, Várez A. Production of alumina parts by powder injection molding with a binder system based on high density polyethylene. J. Eur. Ceram. Soc. 2008; 28(4):763-71.
[9] Coleman AJ, Murray K, Kearns M, Tingskog TA, Sanford B, Gonzalez E. Processing and properties of MIM AISI 4605 via master alloy routes. In Advances in powder metallurgy & particulate materials-2012: proceedings of the 2012 international conference on powder metallurgy & particulate materials sponsored by the Metal Powder Industries Federation, 10-13, Nashville, TN 2012 (pp. 4-35). Metal Powder Industries Federation Princeton.
[10] Askari A, Alaei MH, Mehdipoor Omrani A, Nekouee K, Park SJ.Rheological and thermal characterization of aisi 4605 low-alloy steel feedstock for metal injection molding process. Met. Mater. Int. 2020; 26(12):1820–9.
[11] Momeni, V., Zangi, H., Alaei, M.H. Effect of thermal debinding and sintering parameters on the mechanical properties of 4605 mim compact using the rsm. Adv. Mater. Process. Technol., 2021; 1:1–16
[12] Momeni V, Alaei MH, Askari A, Rahimi AH, Nekouee K. Effect of the fraction of steel 4605 powder in the load in injection molding with the use of a polymer-based binder. Met. Sci. Heat Treatment. 2020; 61:777-81.
[13] Momeni V, Askari A, Allaei MH, Zangi H. Investigating the effect of stearic acid on the mechanical, rheological, and microstructural properties of AISI 4605 feedstock for metal injection molding process. Trans. Indian Inst. Met. 2021; 74(9):2161-70.
[14] Momeni, V., Alaei, M. Optimization of injection parameters in metal injection molding of 4605 low alloy steel. Mod. Mech. Eng. 2019; 19(5): 1199–208.
[15] Ebel T. Metal injection molding (MIM) of titanium and titanium alloys. In Handbook of metal Injection Molding, 2019; 1 (pp. 431-60). Woodhead Publishing.
[16] Omar MA, Subuki I, Abdullah N, Hassan N. Production of medical devices prototype through metal injection moulding technique. Mater. Res.Innov. 2009; 13(3):320-2
[17] Lin, K.H. 2011. Wear behavior and mechanical performance of metal injection molded fe–2ni sintered components. Mater. Des., 32(3): 1273–82.
[18] German RM. Injection molding of metals and ceramics. Powder Metall., 1997; 42:157-60.
[19] Hossain A, Choudhury IA, Nahar N, Hossain I, Bin Mamat A. Experimental and theoretical investigation of powder–binder mixing mechanism for metal injection molding. Mater. Manuf. Process. 2015; 30(1):41-6.
[20] Amin SY, Muhamad N, Jamaludin KR, Fayyaz A, Yunn HS. Characterization of the feedstock properties of metal injection-molded WC-Co with palm stearin binder system. Sains Malays. 2014; 43(1):123-8.
[21] Islam ST, Samanta SK, Lohar AK, Bandyopadhyay A. Rheological study of alumina feedstock for a micro-powder injection moulding application. Mater. Res. Express., 2019; 6(9):095204.
[22] Virdhian S, Doloksaribu M, Supriadi S, Balfas NM, Suharno B, Shieddieque AD. Characterization of 17-4 PH stainless steel metal injection molding feedstock using mixing torque data. In IOP Conference Series: Mater. Sci. Eng. 2020; 980(1):012053, IOP Publishing.
[23] Machaka R, Ndlangamandla P, Seerane M. Capillary rheological studies of 17-4 PH MIM feedstocks prepared using a custom CSIR binder system. Powder Technol. 2018; 15(326):37-43.
[24] Zakaria H, Muhamad N, Sulong AB, Ibrahim MH, Foudzi F. Moldability characteristics of 3 mol% yttria stabilized zirconia feedstock for micro-powder injection molding process. Sains Malays. 2014; 43(1):129-36.
[25] Ramli MI, Sulong AB, Muhamad N, Muchtar A, Arifin A. Stainless steel 316L–hydroxyapatite composite via powder injection moulding: rheological and mechanical properties characterisation. Mater. Res. Innov. 2014; 8(18):S6-100.
[26] Li D, Pan D, Zhang C, Wu W, Lu R, Yang Z. Powder injection moulding of Inconel 713C alloy. Powder Metall., 2019; 62(4):240-6.
[27] Sahu, J., Acharya, J., Meikap, B., Optimization of production conditions for activated carbons from tamarind wood by zinc chloride using response surface methodology. Bioresour. Technol.2010; 101(6):1974–82.
[28] Mehdi H, Mishra RS. An experimental analysis and optimization of process parameters of AA6061 and AA7075 welded joint by TIG+ FSP welding using RSM. Adv. Mater. Process. Technol. 2022; 8(1):598-620.
[29] Heaney DF, Greene CD. Molding of components in metal injection molding (MIM). In Handbook of Metal Injection Molding 2019;1 (pp. 105-27). Woodhead Publishing
[30] Hwang KS. Common defects in metal injection molding (MIM). In Handbook of Metal Injection Molding 2012;1 (pp. 253-69). Woodhead Publishing.
[31] Mohamad NN, Muhamad N, Jamaludin KR, Ahmad S, Ibrahim MH. Flow behavior to determine the defects of green part in metal injection molding. Int. J. Mech. .Mater. .Eng., 2009; 4(1):70-5.
