Investigation the weld quality characterizations and temperature field in laser welding of dissimilar Nickle-base alloy Inconel 600 and duplex stainless steel
الموضوعات : فصلنامه شبیه سازی و تحلیل تکنولوژی های نوین در مهندسی مکانیکAhmad Soleimani 1 , Mohammad Akbari 2 , Arash Karimipour 3 , Amir Homayoun Meghdadi 4 , Reza Nosouhi 5
1 - Department of Mechanical Engineering, Najafabad Branch, Islamic Azad University, Najafabad, Iran
2 - Department of Mechanical Engineering, Najafabad Branch, Islamic Azad University, Najafabad, Iran.
3 - Najafabad Branch,Islamic Azad UniversityMechanical Engineering Department
4 - Associate Professor
5 - Department of Mechanical Engineering, Faculty of Engineering, Najafabad Branch, Islamic Azad University, Najafabad, Isfahan, Iran
الکلمات المفتاحية: dissimilar materials, laser welding, Inconel 600 superalloy, duplex stainless steel, molten pool,
ملخص المقالة :
laser welding of dissimilar materials joint composed of Inconel 600 superalloy and stainless steel of duplex 2205 was performed via experimental design to analyze the weld quality characterization including the weld penetration depth and width and the microstructural variation at different regions of the weld bead. The process parameters impact on the temperature gradient near the boundary line of the fusion zone and base metals of both material according to the variation of focal distance, beam deviation direction to each material and welding speed were investigated. Additionally, variation in weld bead width, depth of weld penetration and appearance of weld bead surface were investigated according to the mentioned process parameters. The results imply that by moving the laser beam in direction of the duplex steel the width of the melt pool was more than that of super alloy 600. Due to the laser beam's high energy density and the melt pool depth remained relatively unchanged when welding at the focal point, as opposed to welding at higher focal distances. With the interaction effect of laser beam deflection of towards the Inconel 600 and increasing focal length due to a lower absorption coefficient and a significant reduction in energy density, the maximum reduction rate of molten pool depth was observed. The maximum weld bead width occurs at the place of laser beam radiation at the center line of the of two parts junction.
[1] G. Ma, D. Wu, D. Guo, Segregation characteristics of pulsed laser butt welding of Hastelloy C-276, Metall. Mater. Trans. A 42 (13) (2011) 3853–3857.
[2] T.J. Lienert, P. Burgardt, K.L. Harada, R.T. Forsyth, T. DebRoy, Weld bead center line shift during laser welding of austenitic stainless steels with different sulfur content, Scr. Mater. 71 (2014) 37–40
[3] Hejripour F, Aidun DK. Consumable selection for arc welding between stainless steel 410 and inconel 718. J Mater Process Technology 2017; 245:287–99.
[4] Y. Guo, D. Wu, G. Ma, D. Guo, trailing heat sink effects on residual stress and distortion of pulsed laser welded Hastelloy C-276 thin sheets, J. Mater. Processing Technology. 214 (12) (2014) 2891–2899.
[5] Y. Li, H. Xu, F. Zhu, L. Wang, Low temperature anodic nitriding of AISI 304 austenitic stainless steel, Mater. Lett. 128 (2014) 231–234.
[6] Dongjiang Wu, Bo Cheng, Jun Liu, Dehua Liu, Guangyi Ma, Zhenqiang Yao, Water cooling assisted laser dissimilar welding with filler wire of nickel-based alloy/austenitic stainless steel, Journal of Manufacturing Processes, Vol 45, September 2019, Pages 652-660.
[7] Naffakh, H., M. Shamanian, and F. Ashrafizadeh. "Dissimilar welding of AISI 310 austenitic stainless steel to nickel-based alloy Inconel 657." Journal of materials processing technology 209.7 (2009): 3628-3639.
[8] Siyu Zhou, Dongsheng Chai, Fangyong Niu, Jinfei Dong, Dongjiang Wu, Helin Zou, Nickel-based alloy/austenitic stainless steel dissimilar weld properties prediction on asymmetric distribution of laser energy, Optics & Laser Technology, Volume 81, July 2016, Pages 33-39.
[9] Sidharth Dev, K. Devendranath Ramkumar, N. Arivazhagan, R. Rajendran, Investigations on the microstructure and mechanical properties of dissimilar welds of inconel 718 and sulphur rich martensitic stainless steel, AISI 416, Journal of Manufacturing Processes, Volume 32, April 2018, Pages 685-698.
[10] Bo Cheng, Dongjiang Wu, Kaojie Yue, Guangyi Ma, Fangyong Niu, Effect of low-temperature cooling on corrosion properties of laser welding Hastelloy C-276/304 stainless steel with filler wire, Optics & Laser Technology, Volume 148, April 2022, 107755.
[11] G. Shanthos Kumar, S. Saravanan, K. Raghukandan, Effect of heat input on microstructure and mechanical properties of laser welded dissimilar grade nickel alloys, Optik, Volume 248, December 2021, 168106.
[12] G. Krishna Kumar, C. Velmurugan, R.S. Jayaram, M. Manikandan, Effect of laser welding process parameters on dissimilar joints of AISI 316 and nickel 201, Materials Today: Proceedings , Volume 22, Part 4, 2020, Pages 2964-2973.
[13] Sunder, S.S.S., Dewangan, S. Critical Analysis into Mechanical Properties and Microstructure of Dissimilar Welded Joint Between Stainless Steel-304 and Inconel-718. J. Inst. Eng. India Ser. D (2023).
[14] Vishwa Bhanu, Dariusz Fydrych, Ankur Gupta, Chandan Pandey, Study on Microstructure and Mechanical Properties of Laser Welded Dissimilar Joint of P91 Steel and INCOLOY 800HT Nickel Alloy, Materials, 2021, 14, 5876.
[15] Gaurav Dak, Chandan Pandey, Experimental investigation on microstructure, mechanical properties, and residual stresses of dissimilar welded joint of martensitic P92 and AISI 304L austenitic stainless steel, International Journal of Pressure Vessels and Piping Volume 194, Part A, 1 December 2021, 104536.
[16] P. Thejasree, N. Manikandan, Ramesh Raju, K.L. Narasimhamu, G.M. Surendranatha, A.K. Damodaram, Investigations on laser beam welded Inconel 718 weldments, Materials Today: Proceedings , Volume 68, Part 5, 2022, Pages 1757-1761.
[17] ASM Handbook, volume 24A, Chapter 7: Duplex Stainless Steels, 2008.
[18] ASM Handbook Volume 2: Properties and Selection: Nonferrous Alloys and Special-Purpose Materials, ASM International, 1990.
