Effect of Laser Parameters on Geometry of Cladded Stellite 6 on 35CrMo Steel Substrate and its Characterization
الموضوعات :Bahman Mansouri 1 , Mahdi Rafiei 2 , Iman Ebrahimzadeh 3 , Farid Naeimi 4 , Masoud Barekat 5
1 - Advanced Materials Research Center, Department of Materials Engineering, Najafabad Branch, Islamic Azad University, Najafabad, Iran.
2 - Advanced Materials Research Center, Department of Materials Engineering, Najafabad Branch, Islamic Azad University, Najafabad, Iran.
3 - Advanced Materials Research Center, Department of Materials Engineering, Najafabad Branch, Islamic Azad University, Najafabad, Iran.
4 - Advanced Materials Research Center, Department of Materials Engineering, Najafabad Branch, Islamic Azad University, Najafabad, Iran.
5 - Faculty of Materials and Manufacturing Engineering, Malek Ashtar University of Technology, Tehran. Iran.
الکلمات المفتاحية: Laser cladding, Microstructure, Stellite 6, 35CrMo alloy steel, Overlapping, Microhardness. ,
ملخص المقالة :
In this research, laser cladding of Stellite 6 on the 35CrMo substrate was done. Various parameters of the laser caldding process were studied and after optimization of the parameters, microstructure and microhardness were evaluated. Characterization of the cladded layer was done by scanning electron microscope, X-ray diffraction, and Vickers microhardness. The results show that the clad track height was dependent on the parameters of the powder feeding rate and the laser scanning speed, and the laser power had the minimal effect. Similarly, the clad track width was controlled by the laser power and laser scanning speed. The clad track dilution was proportional to the laser power and had the greatest impact compared to other parameters. The wetting angle was controlled by three parameters: laser power, laser scanning speed, and powder feeding rate. Laser power of 550 W, powder feeding rate of 0.6 g/s, and laser scanning speed of 10 mm/s were chosen as the optimal parameters. The results showed a good metallurgical bonding between the cladding and the substrate. The microstructure of the single clad track was dense and crack- and pore-free, and due to the thermal and concentration gradient changes during solidification, it consisted of three different areas, including planar, columnar dendritic, and equiaxed dendritic microstructures. A significant improvement in the microhardness of Stellite 6 cladding was observed as compared with the substrate. By increasing the overlapping ratio from 30 to 60%, the dilution rate decreased from 31 to 7%. As a result, the microhardness reached 361 HV in the overlapping ratio of 30% and further to 452 HV in the overlapping ratio of 60%. The overlapping ratio of 60% between adjacent passes created the best results.
[1] Wang W, Zheng XT, Yu JY, Lin W, Wang CG, Xu JM. Time dependent ratcheting of 35CrMo structural steel at elevated temperature considering stress rate. Mater High Temp 2017; 34: 172– 178.
[2] Zhang JW, Lu LT, Shiozawa K, Zhou WN, Zhang WH. Effect of nitrocarburizing and post oxidation on fatigue behavior of 35CrMo alloy steel in very high cycle fatigue regime. Int J Fatigue. 2011;33(7):880-886.
[3] Yue W, Sun XJ, Wang CB, Fu ZQ, Liu YD, Liu JJ. A comparative study on the tribological behaviors of nitride and sulfur-nitrided 35CrMo steel lubricated in PAO base oil with MoDTC additive. Tribol Int 2011;44(12):2029- 2034.
[4] Fernands FAP, Herk SC, Pereira RG, Picon CA, Nascente PAP, Casteletti. LC. Ion nitriding of a superaustenitic stainless steel: wear and corrosion characterization. Surf Coat Technol 2010; 204:3087–90.
[5] Cassar G, Avelar-Batista Wilson JC, Banfield S, Housden J, Matthews A, Leyland. A. A study of the reciprocating sliding wear performance of plasma surface treated titanium alloy. Wear 2010; 269:60–70.
[6] Tang WY, Chuang MH, Chen HY, Yeh JW. Microstructure and mechanical performance of new Al0.5CrFe1.5MnNi0.5 high entropy alloys improved by plasma nitriding. Surf Coat Technol 2010; 204:3118–3124.
[7] Wang HD, Zhuang DM, Wang KL, Liu JJ. Anti-scuffing properties of ion sulfide layers on three hard steels. Wear 2002; 253:1207–1213.
[8] Wang HD, Zhuang DM, Wang KL, Liu JJ. Comparison of the tribological properties of an ion sulfurized coating and a plasma sprayed Fes coating. Mater Sci Eng 2003; 357:321–327
[9] Xiao ZB, Huang YC, Liu Y. Plastic deformation behavior and processing maps of 35CrMo steel. J Mater Eng Perform 2016; 25:1219–1227
[10] Zhang J, Xue Q, Li S-X, Qin Z. Microstructure, corrosion and tribological properties of Ti(CN) multilayer coatings on 35CrMo steel by CVD. Rare Met 2014; 22:1314-1320.
[11] Jendrzejewski R, Conde A, De Damborenea J , Sliwinski G. Characterisation of the Laser-Clad Stellite Layers for Protective Coatings.Mater Des 2002;23:83-88.
12] Toyserkani E, Khajepour A, Corbin S. Laser Cladding, CRC PRESS 2005
[13] Arias-Gonzalez F, del Val J, Comesana R, Penide J, Lusquinos F, Quintero F, Riveiro A, Boutinguiza M, Pou J. Laser claddingof phosphor bronze. Surf Coat Technol 2017; 313:248–254
[14] Lisiecki A, lizak D, Kukofka A. Robotized Fiber Laser Cladding of Steel Sustrate by Metal Matrix Composite Powder at Cryogenic Conditions, Mater Perform Charact 2019; 8: 1214-1225
[15] De Olivera U, Ocelik V, DE Hosson JThM. Analysis of coaxial laser cladding processing condition. Surf Coat Technol 2005; 197: 127-136
[16] Barnes S, Timms N, Bryden B, Pashby I. High power diode laser cladding. J Mater Process Tech 2003; 138: 411-416
[17] Ocelik V, Nenadl O, Palavra, DE Hosson JThM. On the geometry of coating layers formed by overlap. Surf Coat Technol 2014; 242 :54-61
[18] Nemecek S, Fiserova P. The Corrosion Resistance of Laser-Cladded Layers, Conf. Laser Application in Industry 2015; 16:18-3
[19] Xu GH, Kutsuna M. Characteristics of multilayer laser cladding using powder mixture of Co based alloy and Vanadium carbide. Mater Sci Technol 2008; 24:73-84
[20] Hou QY, Gao JS, Zhou F. Microstructure and wear characteristics of cobalt-based alloy deposited plasma transferred arc weld surfacing. Surf Coat Technol 2005, 194 (2–3) :238–243.
[21] Farnia A, Malek Ghaini F, Rao JC, Ocelík V, De Hosson ThM. Effect of Ta on the microstructure and hardness of Stellite 6 coating deposited by low power pulse laser treatments. Surf Coat Technol 2012; 213:278-284.
[22] Sh OC, Doh UM, Yoon IK, Lee Dl, Kim JS. Effect of molybdenum on the microstructure and wear resistance of cobalt-base Stellite hardfacing alloys. Surf Coat Technol 2003;166: 117-126.
[23] Tottel CR. An Encycloprdia of Metallurgy and Material British. Library catalog in publication elata 1984; 311
[24] Sidhu TS, Prakash S, Agrawal RD. Studies of the metallurgical and mechanical properties of high velocity oxy- fuel sprayed stellite-6 coatings on Ni- and Fe-based superalloys. Surf Coat Technol 2006;201: 273-281.
[25] Opris CD, Liu R, Yao MX, Wu XJ. Development of Stellite alloy composites with sintering/HIPing technique for wear-resistant applications. MaterDesign 2007; 28:581-591
[26] Valsecchi B, Previtali B, Gariboldi E, Liu A. Characterisation of the Thermal Damage in a Martensitic Steel Substrate Consequent to Laser Cladding Process.Phys Eng 2011 ;10: 2851- 2856
[27] Chang S, Wu H, Chen C. Impact Wear Resistance of Stellite 6 Hardfaced Valve Seats with Laser Cladding.Mater Manuf Process. 2008; 23:708-713
[28] Lin C, Chen C. Characteristics of Thin Surface Layers of Cobalt-Based Alloys Deposited by Laser Cladding.Surf Coat Technol 2006;200: 4557-4563,
[29] Sun S, Durandet Y, Brandt M. Parametric investigation of pulsed Nd: YAG laser cladding of stellite 6 on stainless steel. Surf Coat Technol 2005; 194:225– 231.
[30] D Oliveira A, Silva P, Vilar R. Microstructural features of consecutive layers of Stellite6 deposited by laser cladding. Surf Coat Technol 2002; 153:203–209.
[31] Xu G. Kutsuna M. Cladding with Stellite6/WC using a YAG laser robot system, Surf Eng 2006; 22:345-352
[32] Toyserkani S, Khajepour E, Corbin A. Three-dimensional finite element modeling of laser cladding by powder injection: effects of powder feedrate and travel speed on the process, J Laser Appl 2003; 15:153–160.
[33] Barekat M, ShojaRazavin R, Ghasemi A. Nd: YAG laser cladding of Co–Cr–Mo alloy on γ-TiAl substrate. Opt Laser Technol 2016; 80:145–152
.[34] Pinkerton A.J. University of Manchester, Laser direct metal deposition: theory and applications in manufacturing and maintenance, in: D.K.Y. Low, J. Lawrence, J. Pou, E. Toyserkani (Eds.), Relat. Titles Adv. Laser Mater. Process. Technol. Res. Appl., Woodhead Publishing Limited, UK. 2010.
[35] Ebrahimzadeh H, Mousavi SAAA. Investigation on pulsed Nd: YAG laser welding of 49Ni–Fe soft magneticalloy. Mater Des 2012; 38:115–123.
[36] Sudand W, Williams S. Investigation of the effects of basic laser material parameters in laser welding. J Laser Appl 2012; 24:032009.
[37] Hofmeister W, Griffith M. Solidification in direct metal deposition by LENS Processing. Met Mater Soc 2001; 53:30–34.
[38] Ding L, Hu S.S, Quan X.M, Shen J.Q. Effect of VN alloy addition on the microstructure and wear resistance of Co- based alloy coatings. J Alloys Comp 2016, 659,8–14.
[39] Gholipour A, Shamanian M, Ashrafizadeh F. Microstructure and wear behavior of stellite 6 cladding on 17-4 PH stainless steel. J Alloys Comp 2011; 509:4905–4909.
[40] Kou S. Welding Metallurgy.JohnWiley and Sons, New Jersy, 2003.
[41] Fouilland L, Mansori M El, Massaq A, Mater J. Friction-induced work hardening of cobalt- base hardfacing deposits for hot forging tools. j Mater Proc Technol 2009; 209: 3366–3373.
[42] Chena B, Sua Y, Xieb Z, Tana C, Fenga J. Development and characterization of 316L/Inconel625 functionally graded material fabricated by laser direct metal deposition. Opt Lasers Techno 2020; 123:105916.
[43] Naghiyan M, Shoja-Razavi R, Mansouri H, Jamali H. Microstructure investigation of Inconel 625 coating obtained by laser cladding and TIG cladding m. Surf Coat Technol 2018; 353:25-31.
[44] Fenga K, Chena Y, Denga P, Lic Y, Zhaoc H, Lua F, Lid F, Huanga J, Lia Z, Improved hightemperature hardness and wear resistance of Inconel625 coatings fabricated by laser cladding. J Mater Process Tech 2017; 243: 82–91.
