Experimental and Numerical Investigation of Thickness on the Shrinkage and out of Roundness in Cylindrical Parts in Injection Molding Process

الموضوعات : فصلنامه شبیه سازی و تحلیل تکنولوژی های نوین در مهندسی مکانیک

ناتان جعفریان جم ¹ (استادیار، دانشکده مکانیک، دانشگاه آزاد اسلامی واحد پردیس)
پیام سرائیان ² (استادیار، دانشکده مکانیک، دانشگاه آزاد اسلامی واحد نجف اباد)
آیت اله عرب امین ابادی ³ (کارشناس ارشد، دانشکده مکانیک، دانشگاه آزاد اسلامی واحد نجف اباد)

تاريخ الإرسال : 14 الأحد , ذو الحجة, 1436 تاريخ التأكيد : 14 الأحد , ذو الحجة, 1436 تاريخ الإصدار : 19 الأحد , صفر, 1435

الکلمات المفتاحية: Polypropylene, Shrinkage, Out of roundness, 3D optical coordinate measuring machine, MOLDFLOW software,

ملخص المقالة :

Injection molding process is one of the most important methods of forming in the plastics manufacturing industry. Shrinkage and out of roundness are phenomenons that affect the final product quality. In this study, the effect of the thickness of cylindrical parts from polypropylene material on shrinkage and out of roundness has been investigated. For this purpose, injection molding process is simulated and analyzed with MOLDFLOW software. Then a five-cavity injection mold from hallow cylindrical parts with five different thicknesses is made. Using an injection molding machine least five samples of these parts are made. Then dimensions of samples are measured using 3D optical coordinate measuring machine and the amount of shrinkage of each sample is obtained. It can be concluded that with increasing part thickness, shrinkage and out of roundness are increased. It is because of being slower at melting material cools and having more time to make crystals. More crystallize caused to more shrinkage and more out of roundness. At the end, the simulation results are compared with the experimental results and showed a good agreement.

المصادر:

]1[ آیت اللهی، م. ، غفوری­آهنگر، ر. ,  صداقت، ا.، فرایند تزریق پلاستیک شبیه سازی به کمک نرم افزارMOLDFLOW به همراه چند مثال صنعتی، تهران، جهاد دانشگاهی دانشگاه صنعتی امیرکبیر، 1389، 260 صفحه.

]2[کرافورد، آر. جی.، /کوکبی، م.، مهندسی پلاستیک، تهران، دانشگاه تربیت مدرس، مرکز نشر آثار علمی،1385، 695 صفحه.

[3] Jafarian A. R., Shakeri M., Investigating the Influence of Different Process Parameters on Shrinkage of Injection-molded Parts, American Journal of Applied Sciences, vol. 2(3), 2005, pp. 688-700.

 [4]          Chiang K.T., Chang F.P., Analysis of shrinkage and warpage in an injection-molded part with a thin shell feature using the response surface methodology, The International Journal of Advanced Manufacturing Technology, 2006, vol. 35, 2006, pp. 468-479.

 [5]          Wu C.-H.,  Huang Y.-J., The influence of cavity deformation on the shrinkage and warpage of an injection-molded part, The International Journal of Advanced Manufacturing Technology, 2006, vol. 32, 2006, pp. 1144-1154.

 [6]          Shie J.-R., Optimization of injection molding process for contour distortions of polypropylene composite components by a radial basis neural network, The International Journal of Advanced Manufacturing Technology, 2007, vol. 36, 2007, pp. 1091-1103.

[7]           Santis F. D., Pantani R., Speranza V., Titomanlio G., As-mol