Conceptual Design of Single-Acting Oleo-Pneumatic Shock Absorber in Landing Gear with Combined Method
الموضوعات : فصلنامه شبیه سازی و تحلیل تکنولوژی های نوین در مهندسی مکانیکNima Ghiasi Tabari 1 , Saeed Mahdiyeh Borojeni 2
1 - Department of Mechanical Engineering, Dashtestan Branch, Islamic Azad University, Boushehr, Iran
2 - Department of Mechanical Engineering, College of Mechanical Engineering, Dashtestan Branch, Islamic Azad University, Borazjan, Iran
الکلمات المفتاحية: shock absorber, landing gear, hydro pneumatic shock absorber,
ملخص المقالة :
Landing gear is a structure that is mounted under the fuselage and helps the aircraft in takeoffs and landings. The most important duty of landing gear is the control of vibration exerted on the system through the shock absorber which is a common component to all the landing gear. Considering the importance of this issue, the necessity of investigating shock absorber with features such as high efficiency, reliability and maintenance, etc. is undeniable. In the present study In addition to choosing hydro pneumatic shock absorber its relationships arising from oil and gas liquids have been studied. This research was conducted with the aim of reducing the force variations and vibrations, with a focus on liquid gas. Thus, according to the gas laws, initially gas flow in the case of practical modes of isotherms during the taxi and poly trophic during landing has been studied. Considering that in the shock absorber only one mode can be used and Isotherms mode despite less vibration is not responsible for the landing phase and poly trophic mode exerts a lot of vibration on the fuselage, therefore a situation that can meet both needs in a way that have both phases of taxing and landing and at the same time reducing vibrations to be followed is the combination mode that its relation has been extracted at the end. The results of the extracted relations using numerical methods compared with practical results shows that not only the force on the aircraft body but also the vibrations on it have been significantly reduced and improves system performance.
[1] G. MikuÃlowski, Adaptive impact absorbers based on magneto rheological fluids, Smart Institute of Fundamental Technological Research Polish Academy of Sciences Technology Centre, 2007.
[2] Anon., FAR Part 25 Airworthiness Standards: Transport Category Airplanes, Federal. Aviation Administration, Washington, DC, October 1994.
[3] Currey, N. S., Aircraft Landing Gear Design: Principles and Practices, AIAA Education Series, Washington, 1988.
[4] Bauer, Wolfgang, Hydro pneumatic Suspension Systems, Springer-Verlag Berlin Heidelberg, 2011.
[5] Chai, S, Mason, W. H., Landing Gear Integration in Aircraft Conceptual Design, NASA Ames Research Center under Grant NAG-2-919, September 1996.
[6] Emami, M. D. Mostafavi, S. A. Asadollahzadeh, P. Modeling and simulation of active hydro-pneumatic suspension System through bond graph, ISSN 1392 - 1207. MECHANIKA. 2011.
[7] Batterbee, D.C., Sims, N.D., Stanway, R. and Wolejsza, Zbigniew, Magneto rheological landing gear: 1. A design methodology. Smart Materials and Structures, 16 (6), (2007).
[8] Akhilesh, Jha, Landing Gear Layout Design for Unmanned Aerial Vehicle, 14th National Conference on Machines and Mechanisms (NaCoMM09), NIT, Durgapur, India, December 17-18, 2009.
[9] Greenbank, S. J., “Landing Gear: The Aircraft Requirement,” Institution of Mechanical Engineers, Proceedings, Part G, Journal of Aerospace Engineering, Vol. 205, 1991.
[10] Khani, Mahboubeh, Magneto-Rheological (MR) Damper For Landing Gear System, MSc Thesis, Concordia University, June 2010.
[11] J. Roskam, Airplane Design Part IV: Layout of Landing Gear and Systems, DAR Corporation, 2010.
[12] N. Paletta, “An Automatic Procedure for the Landing Gear Conceptual Design of a Light Unmanned Aircraft”, SAE International, 2013.
[13] Hiemenz, Gregory, Adaptive MR Shock Absorber For High Speed Watercraft Seat, TECHNO –SCIENCE,14 June 2011.
