Tolerance Analysis of the Trigger Mechanism Assembly Using Direct Linearization Method

Subject Areas : Journal of Simulation and Analysis of Novel Technologies in Mechanical Engineering

عبدالعلی مراثی ¹ , محمد سالم ²

1 - استادیار، دانشکده مکانیک، دانشگاه صنعتی مالک اشتر
2 - دانشجوی کارشناسی ارشد، دانشکده مکانیک، دانشگاه صنعتی اصفهان

Received: 2015-09-30 Accepted : 2015-09-30 Published : 2009-12-22

Keywords: DLM, Tolerance Analysis, Mechanical assembly,

Abstract :

Tolerance analysis of mechanical assemblies is an important tool in reliable design of products at low cost and good quality. Using this tool, it is possible in manufacturing stage to observe the effect of parameters on assembly requirements. The direct linearization method is a useful method which runs based on vector loop analysis. In this research, the DLM method is used to analyze the tolerance chain in triggering mechanism assembly. Furthermore the percent contribution of various manufacturing dimensions on the design requirement of the assembly in determined.

References:

[1] Li L., H., Yang L. Guo et al., A control method of guide rolls in 3D-FE simulation of ring rolling, Journal of Materials Processing Technology, vol. 205, no. 1-3, 2008, pp. 99-110.

[2] Allwood J. M., A Structured Search for Novel Manufacturing Processes Leading to a Periodic Table of Ring Rolling Machines, Journal of Mechanical Design, vol. 129, no. 5, 2007,
pp. 502-511.

[3] Joun M. S., Chung J. H., , Shivpuri R., An axisymmetric forging approach to preform design in ring rolling using a rigid-viscoplastic finite element method, International Journal of Machine Tools and Manufacture, vol. 38,
no. 10-11, 1998, pp. 1183-1191.

[4] Yang D. Y., Ryoo J. S., An Investigation into the Relationship between Torque and Load in Ring Rolling, Journal of Engineering for Industry, vol. 109, no. 3, 1987, pp. 190-196.

[5] M. Wang, H. Yang, Z. C. Sun et al., Analysis of coupled mechanical and thermal behaviors in hot rolling of large rings of titanium alloy using 3D dynamic explicit FEM, Journal of Materials Processing Technology, vol. 209, no. 7, 2009, pp. 3384-3395.

[6] Hua L., Qian D., Analysis of plastic penetration in process of groove ball-section ring rolling, Journal of Mechanical Science and Technology, vol. 22, no. 7, 2008, pp. 1374-1382.

[7] Song J. L., Dowson A. L., Jacobs et al. M. H., Coupled thermo-mechanical finite-element modelling of hot ring rolling process, Journal of Materials Processing Technology, vol. 121, no. 2-3, 2002, pp. 332-340.

[8] Hua L., Qian D., Pan L., Deformation behaviors and conditions in L-section profile cold ring rolling, Journal of Materials Processing Technology,
vol. 209, no. 11, 2009, pp. 5087-5096.

[9] Kim K. H., Suk H. G., Huh M. Y., Development of the profile ring rolling process for large slewing rings of alloy steels, Journal of Materials Processing Technology, vol. 187-188, 2007, pp. 730-733.

 

[10] Wang M., H., Yang Z.. Sun et al., Dynamic explicit FE modeling of hot ring rolling process, Transactions of Nonferrous Metals Society of China, vol. 16, no. 6, 2006,
pp. 1274-1280.

[11] Forouzan M. R., Salimi M., Gadala M. S. , Guide roll simulation in FE analysis of ring rolling, Journal of Materials Processing Technology, vol. 142, no. 1, 2003, pp. 213-223.

[12] Chabin D., Emptas P. Y., Bouzaiane M., Numerical simulation of ring rolling process, Application to superalloy 718 parts, AIP Conference Proceedings, vol. 907, no. 1, 2007, pp. 1366-1371.

[13] Moon H. K., Lee M. C., Joun M. S., Predicting polygonal-shaped defects during hot ring rolling using a rigid-viscoplastic finite element method, International Journal of Mechanical Sciences, vol. 50, no. 2, 2008,
pp. 306-314.

[14] Qian D., L., Hua L., Research on gripping conditions in profile ring rolling of raceway groove, Journal of Materials Processing Technology, vol. 209, no. 6, 2009pp. 2794-2802.

[15] DEFORM-3D Software, Version 6.1, 2007.