Application of Piezoelectric and Functionally Graded Materials in Designing Electrostatically Actuated Micro Switches

Subject Areas : Engineering

A  Hosseinzadeh ¹ (Center of Excellence in Design, Robotics and Automation (CEDRA), School of Mechanical Engineering, Sharif University of Technology)
M.T  Ahmadian ² (Center of Excellence in Design, Robotics and Automation (CEDRA), School of Mechanical Engineering, Sharif University of Technology)

Received: 2010-06-24 Accepted : 2010-07-23 Published : 2010-06-30

Keywords: Microbeam, Functionally graded material, Piezoelectric, Static and dynamic instability,

Abstract :

In this research, a functionally graded microbeam bonded with piezoelectric layers is analyzed under electric force. Static and dynamic instability due to the electric actuation is studied because of its importance in micro electro mechanical systems, especially in micro switches. In order to prevent pull-in instability, two piezoelectric layers are used as sensor and actuator. A current amplifier is used to supply input voltage of the actuator from the output of the sensor layer. Using Hamilton’s principle and Euler-Bernoulli theory, equation of motion of the system is obtained. It is shown that the load type (distributed or concentrated) applied to the micro beam from the piezoelectric layer, depends on the shape of the actuator layer (E.g. rectangle, triangular). Finite element method is implemented for evaluation of displacement field in the micro beam and dynamic response of the micro beam under electric force is calculated using finite difference method. Effect of squeeze film damping on pull-in voltage and time-response of the system is considered using nonlinear Reynolds equation. Effect of several parameters such as gain value between piezoelectric sensor and actuator layer, profile of functionally material, and geometry of the system is considered on dynamic behavior of the micro beam especially on pull-in instability. Results are verified for simple cases with previous related studies in the literature and good agreements were achieved. Results indicate that increasing gain value between sensor and actuator enhances stiffness of the system and will raise pull-in voltage. Also, dependency of dynamic properties of the system such as amplitude and frequency of vibration on functionally graded material profile is shown. The material distribution of the functionally graded material is designed in such a way that results in a specific pull-in voltage.

References:

[1] Hu Y.C., Chang C.M., Huang S.C., 2004, Some design considerations on the electrostatically actuated microstructures, Sensors and Actuators A 112: 155-161.

[2] Osterberg P.M., 1995, Electrostatically Actuated Micro Electromechanical Test Structures for Material Property Measurement, PhD dissertation, Massachusetts Institute of Technology.

[3] Ahmadian M.T., Borhan H., Esmailzadeh E., 2009, Dynamic analysis of geometrically nonlinear and electrostatically actuated micro-beams, Communications in Nonlinear Science and Numerical Simulation 14(4): 1627-1645.

[4] Nayfeh A.H., Younis M.I., 2004, A new approach to the modeling and simulation of flexible microstructures under the effect of squeeze film damping, Journal of Micromechanics and Microengineering, 14(2): 170-181.

[5] Moghimi Zand M., Ahmadian M.T., 2009, Vibrational analysis of electrostatically actuated microstructures considering nonlinear effects, Communications in Nonlinear Science and Numerical Simulation, 14(4): 1664-1678.

[6] Lin Ch.-Ch., Huang H.-N., 1999, Vibration control of beam-plates with bonded piezoelectric sensors and actuators, Computers and Structures 73: 239-248.

[7] Collet M., Walter V., Delobelle P., 2003, Active damping of a micro-cantilever piezo-composite beam, Journal of Sound and Vibration 260: 453-476.

[8] Meirovitch L., 1997, Principles and Techniques of Vibrations, Englewood Cliffs, Prentice Hall Inc, Nj.

[9] Moheimani R., Fleming A.J., 2006, Piezoelectric Transducers for Vibration Control and Damping (Advances in Industrial Control), First Edition, Springer.

[10] Preumont A., 2006, Mechatronics: Dynamics of Electromechanical and Piezoelectric Systems, Springer.

[11] Najafizadeh M.M., Eslami M.R., 2002, First-order theory based thermo elastic stability of functionally graded material circular plates, AIAA Journal 40: 1444-1450.

[12] Veijola T., Kuisma H., Lahdenpera J., Ryhanen T., 1995, Equivalent-circuit model of the squeezed gas film in a silicon accelerometer, Sensors and Actuators A 48: 235-248.

[13] Jang D.S., Kim D.E, 1996, Tribological behavior of ultra-thin soft metallic deposits on hard substrates, Wear 196: 171-179.

[14] Moghimi Zand M., Ahmadian M.T., 2007, Characterization of coupled-domain multi-layer micro plates in pull-in phenomenon, vibrations and dynamics, International Journal of Mechanical Sciences 49: 1226-1237.

[15] Krylov S., 2007, Lyapunov exponents as a criterion for the dynamic pull-in instability of electrostatically actuated microstructures, International Journal of Non-Linear Mechanics 42(4): 626-642.