CFD Modelling of Friction Stir Welding of Aluminum to Steel butt joint

Subject Areas : Welding

Hamed Aghajani Derazkola ¹ , Majid Elyasi ² , Morteza Hossienzadeh ³

1 - Young Researchers and Elite Club, Sari Branch, Islamic Azad University, Sari
2 - Department of mechanical Engineering, Noshiravani University of Technology, Babol, Iran
3 - IDepartment of Engineering, slamic Azad University of Ayatollah Amoli branch, Iran

Received: 2015-05-31 Accepted : 2015-08-15 Published : 2015-09-01

Keywords: Friction Stir Welding, Dissimilar joint, Computational Fluid Dynamic, Thermal modelling,

Abstract :

In this article effects of friction stir welding (FSW) tool rotational and traverse speeds were studied on heat generation and temperature distribution in welding zone of AA1100 aluminum alloy and A441 AISI joint. Computational fluid dynamics method was used to simulate the process with commercial CFD Fluent 6.4 package. To enhance the accuracy of simulation in this Study, the welding line that is located work-pieces interface, defined with pseudo melt behavior around the FSW pin tool. Simulation results showed that with increase of FSW tool rotational speed, the generated heat became more and dimensions of the stir zone will be bigger. The calculation result also shows that the maximum temperature was occurred on the advancing side. The computed results demonstrated that with increasing tool linear speeds the heat generation experienced growth down trend. With increasing traveling speeds the time to reach maximum temperature in stir zone growth but the tool rotational speed dose not effect on time to reach maximum temperature. The model outcomes show that more than 85% total heat was produced by tool shoulder and the maximum heat with selected parameters in this study was 935 kelvin degrees. The computed results shows that the maximum value of strain rate achieved was 29 S-1 for A441 AISI side and 42 S-1 at AA1100 side.

References:

1. S. Golezani, S. M. Arab, Sh. Javadi and F. Kargar, The Effect of Friction Stir Processing Speed Ratio on the Microstructure and Mechanical Properties of A 430 Ferritic Stainless Steel, Journal of Advanced Materials and Processing, Vol. 2, No. 2, 2014, pp. 39-48.
2. D. Santiago, S. Urquiza, G. Lombera and L. Vedia, 3D Modeling of Material Flow and Temperature in Friction Stir Welding, Soldagem & Inspeção, Vol. 14, No. 3, 2009, pp. 248-256.
3. R. Hamilton, D. MacKenzie and H. Li, Multi-physics simulation of friction stir welding process, Engineering Computations: International Journal for Computer - Aided Engineering and Software, Vol. 27, No. 8, 2010, pp. 967-985.
4. Z. Zhang, H. W. Zhang, A fully coupled thermo-mechanical model of friction stir welding, International Journal of Advanced Manufacturing Technology, Vol. 37, 2008, pp. 279-293.
5. Smith, G. Bendzsak, T. North, J. Hinrichs, J. Noruk and R. Heideman, Heat and Material Flow Modeling of the Friction Stir Welding Process, 11th International Conference on Computer Technology in Welding, Detroit, United State, 1999.
6. T. North, G. Bendzsak and C. Smith, Material Properties Relevant to 3-D Modeling, 2nd International Friction Stir Welding Symposium, Gothenburg, Sweden, 2000.
7. T. U. Seidel, A. P. Reynolds, Two-dimensional friction stir welding process model based on fluid mechanics, Science and Technology of Welding and Joining, Vol. 8, 2003, pp. 175-183.
8. W. Zhang, T. DebRoy, T. A. Palmer and J. W. Elmer, Modeling of ferrite formation in a duplex stainless steel weld considering non-uniform starting microstructure, Acta Materialia, Vol. 53, No. 16, 2005, pp. 4441–4453.
9. R. Nandan, G. Roy and T. DebRoy, Numerical simulation of three dimensional heat transfer and plastic flow during friction stir welding, Metallurgical and Materials Transactions A, Vol. 37, No. 4, 2006, pp. 1247–1259.
10. R. Nandan, G. Roy, T. Lienert and T. DebRoy, Numerical modelling of 3D plastic flow and heat transfer during friction stir welding of stainless steel, Science and Technology of Welding and Joining, Vol. 11, No. 5, 2006, pp. 526-537.
11. H. W. Nassar, M. K. Khraisheh, Simulation of Material Flow and Heat Evolution in Friction Stir Processing Incorporating Melting, Journal of Engineering Materials and Technology, Vol. 134, 2012, pp. 61-67.
12. S. D. Ji, Q. Y. Shi, L. G. Zhang, A. L. Zou, S. S. Gao and L. V. Zan, Numerical simulation of material flow behavior of friction stir welding influenced by rotational tool geometry, Computational Materials Science, Vol. 63, 2012, pp. 218–226.
A. Arora, Z. Zhang, A. Deb and T. DebRoy, Strains and strain rates during friction stir welding, Scripta Materialia, Vol. 61, 2009, pp. 863–866.
13. O. C. Zienkiewicz, I. C. Cormeau, Visco-Plasticity Solution by Finite-Element Process”, Archives of Mechanics, Vol. 24, 1972, pp. 872-889.
14. T. Sheppard, D. S. Wright, Determination of Flow-Stress .1. Constitutive Equation for Aluminum Alloys at Elevated-Temperatures, Metals Technology, Vol. 6, 1979, pp. 215-223.
15. T. Sheppard, D. S. Wright, Determination of Flow-Stress .2. Radial and Axial Temperature Distribution during Torsion Testing, Metals Technology, Vol. 6, 1979, pp. 224-229.
16. E. A. Brandes, G. B. Brool, Smithells Metals Reference Book, 8th Ed, Elsevier, Oxford, 2004.
17. Zener, J. H. Hollomon, Effect of Strain Rate upon Plastic Flow of Steel, Journal of Applied Physics, Vol. 15, 1944, pp. 22-32.
18. T. Sheppard, D. S. Wright, Determination of flow stress: Part 1 constitutive equation for aluminum alloys at elevated temperatures, Metals Technology, Vol. 6, 1979, pp. 215-223.
19. Davis, J. R., Nonferrous, Alloys and Special-Purpose Material, ASM Handbook, Vol. 2, Ohio, 1990.
20. R. Nandan, G. Roy, T. J. Lienert and T. Debroy, Three-dimensional heat and material flow during friction stir welding of mild steel, Acta Materialia, Vol. 55, 2007, pp. 883–895.
21. H. S. Carslaw, J. C. Jaeger, Conduction of heat in solids, 2end Ed, Oxford, Clarendon Press, 1959, pp. 87–89.
22. R. Ayer, H. W. Jin, R. R. Mueller, S. Ling and S. Ford, Interface structure in a Fe–Ni friction stir welded joint, Scripta Materialia, Vol. 53, 2005, pp. 1383-1387.
23. R. Nandan, B. Prabu, A. De and T. Debroy, Improving Reliability of Heat Transfer and Materials Flow Calculations during Friction Stir Welding of Dissimilar Aluminum Alloys, Welding Journal, Vol. 86, 2007, pp. 313-322.
24. T. J. Lienert, W. L. Stellwag, B. B. Grimmett and R. W. Warke, Friction Stir Welding Studies on Mild Steel, Welding Journal, Vol. 82, 2003, pp. 1s-9s.
25. R. Schuhmann, Metallurgical Engineering, Vol. 1: Engineering Principles, Cambridge press, Addison-Wesley Press, 1952.
26. B. C. Liechty, B. W. Webb, Modeling the frictional boundary condition in friction stir welding, International Journal of Machine Tools and Manufacture, Vol. 48, 2008, pp. 1474-1485.
27. P. I. Temple, Aluminum and aluminum alloys, 10st ed., AWS Welding Handbook, Ohio, 1998, Chap1.
28. G. E. Totten, S. MacKenzie, Handbook of Aluminum, Vol. 2, Marcel Dekker, New York, 2003, Chap 6.
29. Y. Weng, H. Dong and Y. Gan, Advanced Steels, Springer-Verlag Berlin Heidelberg and Metallurgical Industry Press, 2011, pp.3-35.