Introduction of CaCO3 as Electron Recombination Barrier Layer in TiO2-Based Dye-Sensitized Solar Cell
Subject Areas : Journal of Environmental Friendly Materials
M Yazdanipanah
1
,
M. R Mohammadi
2
1 - Department of Materials Science and Engineering, Sharif University of Technology, Tehran, Iran
2 - Department of Materials Science and Engineering, Sharif University of Technology, Tehran, Iran
Keywords: DSSC, Surface Modification, Recombination Barrier Layer, Calcium Carbonate,
Abstract :
Calcium carbonate (CaCO3) is an effective material for surface modification in TiO2-based dye-sensitized solar cells (DSSCs). Its higher conduction band position compared to TiO2 helps reduce electron recombination rates, and its elevated isoelectric point promotes increased dye adsorption. It is crucial to control the thickness of the CaCO3 layer to less than 3-10 nm, as tunneling phenomena cannot occur when the insulating layer exceeds 10 nm in thickness. In this study, the CaCO3 layer was deposited using the spin-coating method. Additionally, in two samples, the second TiCl4 treatment was omitted during DSSC preparation to assess its impact on the photovoltaic properties. The results indicate that while the deposition of CaCO3 enhances the photocurrent of the DSSCs, it simultaneously reduces the fill factor. However, applying the TiCl4 treatment both before and after CaCO3 deposition improves the fill factor, leading to greater efficiency compared to the untreated samples. Specifically, sample TT3CT achieved an efficiency of 7.98%, while the neat sample reached 7.58% efficiency
[1] Li W, Liu J, Zhao D. Mesoporous materials for energy conversion and storage devices. Nat. Rev. Mater. 2016; 4;1(6):1-7.
[2] Dambhare MV, Butey B, Moharil SV. Solar photovoltaic technology: A review of different types of solar cells and its future trends. JPCS J. Phys: Conf. Ser. 2021;1913:012053.
[3] Ellabban O, Abu-Rub H, Blaabjerg F. Renewable energy resources: Current status, future prospects and their enabling technology. Renew.Sustain Energy Rev. 2014;1;39:748-64.
[4] Nayak PK, Mahesh S, Snaith HJ, Cahen D. Photovoltaic solar cell technologies: analysing the state of the art. Nat. Rev. Mater. 2019;4(4):269-85.
[5] O'regan B, Grätzel M. A low-cost, high-efficiency solar cell based on dye-sensitized colloidal TiO2 films. Nat. 1991;353(6346):737-40.
[6] Mariotti N, Bonomo M, Fagiolari L, Barbero N, Gerbaldi C, Bella F, Barolo C. Recent advances in eco-friendly and cost-effective materials towards sustainable dye-sensitized solar cells. Green Chem. 2020;22(21):7168-218.
[7] Golvari P, Nouri E, Mohsenzadegan N, Mohammadi MR, Martinez-Chapa SO. A single layer deposition of Li-doped mesoporous TiO2 beads for low-cost and efficient dye-sensitized solar cells. New J Chem. 2021;45(5):2470-77.
[8] Pascoe AR, Bourgeois L, Duffy NW, Xiang W, Cheng YB. Surface state recombination and passivation in nanocrystalline TiO2 dye-sensitized solar cells. J. Phys. Chem. C 2013; 27;117(47):25118-26.
[9] Saxena V, Aswal DK. Surface modifications of photoanodes in dye sensitized solar cells: enhanced light harvesting and reduced recombination. Semicond. Sci. Technol. 2015; 22;30(6):064005.
[10] Sireesha P, Sun WG, Su C, Kathirvel S, Lekphet W, Akula SB, Li WR. Enhancement of power conversion efficiency of TiO2-based dye-sensitized solar cells on various acid treatment. JNN J.Nanosci.Nanotechnol. 2017; 17(1):354-62.
[11] Park SK, Yun TK, Bae JY, Won YS. Combined embedding of N-doping and CaCO3 surface modification in the TiO2 photoelectrodes for dye-sensitized solar cells. Appl. Surf. Sci. 2013;15(285):789-94.
[12] Madhu Mohan V, Murakam K, Jonnalagadda M, Machavaram VR. Improved efficiency in dye-sensitized solar cell via surface modification of TiO2 photoelectrode by spray pyrolysis. J. Mater. Sci.Mater. Electron. 2021;32(13):18231-9.
[13] Brittain HG. Profiles of drug substances, excipients and related methodology. AP Academic Press. 2016; 26.
[14] Racca LM, Bertolino LC, Nascimento CR, de Sousa AM, Reznik LY, Yokoyama L, da Silva AL. Myristic acid as surface modifier of calcium carbonate hydrophobic nanoparticles. JNR J. Nanoparticle Res. 2019;21:1-3..
[15] Hossain FM, Murch GE, Belova IV, Turner BD. Electronic, optical and bonding properties of CaCO3 calcite.Solid-State Commun. 2009;149(29-30):1201-3.
[16] Wang ZS, Yanagida M, Sayama K, Sugihara H. Electronic-insulating coating of CaCO3 on TiO2 electrode in dye-sensitized solar cells: improvement of electron lifetime and efficiency. Chem. Mater. 2006;18(12):2912-16.
[17] Tehare KK, Navale ST, Stadler FJ, He Z, Yang H, Xiong X, Liu X, Mane RS. Enhanced DSSCs performance of TiO2 nanostructure by surface passivation layers. Mater. Res. Bull. 2018; 99:491-5.
[18] Lee S, Kim JY, Youn SH, Park M, Hong KS, Jung HS, Lee JK, Shin H. Preparation of a nanoporous CaCO3-coated TiO2 electrode and its application to a dye-sensitized solar cell. Langmuir. 2007; 23(23):11907-10.
[19] Gharavi PM, Mohammadi MR. The improvement of light scattering of dye-sensitized solar cells aided by a new dandelion-like TiO2 nanostructures. Sol. Energy Mater. Sol. Cells. 2015; 137:113-23.
[20] Khazaei M, Mohammadi MR, Li Y. Dye-sensitized solar cells based on anatase-and brookite-TiO2: enhancing performance through optimization of phase composition, morphology and device architecture. Nanotechnology. 2024; 35(38):385602.