Increasing the Heat Transfer Performance of a Turbulator Equipped Concentric Gas-liquid Heat Exchanger Using Al2O3 – Water Nanofluid
محورهای موضوعی : Mechanical Engineeringseyyed rahim hosseini 1 , Seyyed Masoud Seyyedi 2 , Mehdi Hashemi Tilenoee 3
1 - Department of Mechanical Engineering, Aliabad Katoul Branch, Islamic Azad University, Aliabad Katoul, Iran
2 - Department of Mechanical Engineering,
Aliabad Katoul Branch,
Islamic Azad University, Aliabad Katoul ,
Iran
3 - Department of Mechanical Engineering, Aliabad katoul Branch, Islamic Azad University, Aliabad Katoul, Iran
کلید واژه: Nanofluid, STAR-CCM, turbulators, smooth tube, turbulent,
چکیده مقاله :
In this study, the turbulent fluid flow and heat transfer performance of a concentric two-tube (air-nanofluid) heat exchanger with a helical turbulator is studied using STAR-CCM+. First, the computational code is validated according to the related experimental data and its simulation results for air and water. Then, the heat transfer performance and the effect of the different pitches of the helical turbulators are analyzed by replacing nanofluid instead of water for heat removal. The results show that the turbulator and nanoparticle has a high impact on heat transfer capability of the heat exchanger. The result shows that, the heat transfer is increased using turbulators in comparison with smooth tube for pitches of 15, 30 and 45 mm, respectively. In addition, the STAR-CCM+ is a proper tool for simulation of a complex geometries in three-dimensional. It is not only the CFD solver, STAR- CCM+ is an entire engineering process for solving problems involving flow (of fluids or solids), heat transfer and stress. It provides a suite of integrated components that combine to produce a powerful package that can address a wide variety of modeling needs. These components include: • 3D-CAD Modeler • CAD Embedding • Surface Preparation Tools • Automatic Meshing Technology • Physics Models • Post-processing
[1] Zhnegguo, Zhang, Xu Tao, and Fang Xiaoming. "Experimental study on heat transfer enhancement of a helically baffled heat exchanger combined with three-dimensional finned tubes." Applied Thermal Engineering 24, no. 14-15 (2004): 2293-2300.
[2] Neshumayev, Dmitri, ArvoOts, Jaan Laid, and Toomas Tiikma. "Experimental investigation of various turbulator inserts in gas-heated channels." Experimental Thermal and Fluid Science 28, no. 8 (2004): 877-886.
[3] Yakut, Kenan, and Bayram Sahin. "Flow-induced vibration analysis of conical rings used for heat transfer enhancement in heat exchangers." Applied Energy 78, no. 3 (2004): 273-288.
[4] Yildiz, Cengiz, Yaşar Biçer, and Dursun Pehlivan. "Effect of twisted strips on heat transfer and pressure drop in heat exchangers." Energy Conversion and Management 39, no. 3-4 (1998): 331-336.
[5] Durmuş, Aydın. "Heat transfer and exergy loss in cut out conical turbulators." Energy Conversion and Management 45, no. 5 (2004): 785-796.
[6] Eiamsa-ard, Smith, and PongjetPromvonge. "Enhancement of heat transfer in a tube with regularly-spaced helical tape swirl generators." Solar energy 78, no. 4 (2005): 483-494.
[7] Kurtbaş, İ., Durmuş, A., Eren, H. and Turgut, E., 2007. Effect of propeller type swirl generators on the entropy generation and efficiency of heat exchangers. International Journal of Thermal Sciences, 46(3), pp.300-307.
[8] Gül, H. and Evin, D., 2007. Heat transfer enhancement in circular tubes using helical swirl generator insert at the entrance. International Journal of Thermal Sciences, 46(12), pp.1297-1303.
[9] Zamankhan, P., 2010. Heat transfer in counterflow heat exchangers with helical turbulators. Communications in Nonlinear Science and Numerical Simulation, 15(10), pp.2894-2907.
[10] Eiamsa-ard, S., Pethkool, S., Thianpong, C. and Promvonge, P., 2008. Turbulent flow heat transfer and pressure loss in a double pipe heat exchanger with louvered strip inserts. International Communications in Heat and Mass Transfer, 35(2), pp.120-129.
[11] Naphon, P. and Suchana, T., 2011. Heat transfer enhancement and pressure drop of the horizontal concentric tube with twisted wires brush inserts. International Communications in Heat and Mass Transfer, 38(2), pp.236-241.
[12] Turgut, E., Çakmak, G. and Yıldız, C., 2012. Optimization of the concentric heat exchanger with injector turbulators by Taguchi method. Energy conversion and management, 53(1), pp.268-275.
[13] Şahin, H.M., Baysal, E. and Dal, A.R., 2013. Experimental and numerical investigation of thermal characteristics of a novel concentric type tube heat exchanger with turbulators. International journal of energy research, 37(9), pp.1088-1102.
[14] Şahin, H.M., Baysal, E., Dal, A.R. and Şahin, N., 2015. Investigation of heat transfer enhancement in a new type heat exchanger using solar parabolic trough systems. International journal of hydrogen energy, 40(44), pp.15254-15266.
[15] HashemiKarouei, S.H. and Mousavi Ajarostaghi, S.S., 2021. Influence of a curved conical turbulator on heat transfer augmentation in a helical double‐pipe heat exchanger. Heat Transfer, 50(2), pp.1872-1894.
[16] Yadav, R.K. and Singhai, A., 2020. Heat Transfer Enhancement in a Double Pipe Heat Exchanger using Bio-Nano fluid (Mango-Bark) using CFD. International Journal of Innovative Research in Technology, 6(9), 123-130.