Influence of Vibratory Finishing Process by Incorporating Abrasive Ceramics and Glassy Materials on Surface Roughness of CK45 Steel

Subject Areas : Mechanical Engineering

Payam Saraeian ¹ , Mostafa Gholami ² , Amir Behagh ³ , Omid Behagh ⁴ , Hamid Reza Javadinejad ⁵ , Mohammad Mahdieh ⁶

1 - Department of Materials Engineering, Islamic Azad University of Najafabad Branch, Isfahan, Iran
2 - Department of Materials Engineering, Islamic Azad University of Najafabad Branch, Isfahan, Iran
3 - Arshan Sanat Jam Co. ltd, Isfahan, Iran
4 - Arshan Sanat Jam Co. ltd, Isfahan, Iran
5 - Department of Materials Engineering, Isfahan University of Technology, Isfahan, Iran
6 - UniverSchool of Mechanical Engineering, College of Engineering, University of Tehran, Tehran, Iran sity of Tehran (UT)

Received: 2016-09-12 Accepted : 2016-11-27 Published : 2016-12-24

Keywords: Vibratory finishing, Surface Roughness, Mass finishing, Abrasive particles,

Abstract :

The vibratory finishing is one of the important mass finishing processes. This can be applied for finishing many metallic and non- metallic components using abrasive materials such as steel, ceramic, natural materials and etc. The vibratory finishing process is used for some purposes such as surfaces polishing, deburring, oxide layer removing and rounding the edges. Evaluation of surface roughness changes with time that is one of the important parameters during the vibratory finishing process. In this study, the effects of the working time and abrasive materials are investigated on the surface roughness changes of CK45 steel samples. The ceramic, glass and mixed abrasive particles are used as the abrasive media. The experiments are performed at different time from 10 to 120 minutes in the dry environment. Finally, the surface roughness values of samples were measured and then fitted by a regression equation for description of the surface roughness changes with time. According to the results, the maximum surface finish was obtained after 120 minutes by using mixed abrasive materials. The surface roughness improved approximately 60%.

References:

[1]   Davidson, D. A., “Mass Finishing Processes”, Metal Finishing, Vol. 10, 2007, pp. 72-83.

[2]   Mahdieh M. S., Mahdavinejad R., “Recast Layer and Micro Cracks in Electrical Discharge Machining of Ultra-Fine Grained Aluminum”, Journal of Engineering Manufacture Proceedings of the Institution of Mechanical Engineers, Part B, 2016, pp. 0954405416641326.

[3]   Mahdieh M. S., Mahdavinejad R., “A Study of Stored Energy in Ultra-Fined Grained Aluminum Machined by EDM”, Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, 2016, pp. 0954406216666872.

[4]   Mahdieh M. S., Mahdavinejad R., “A Comparative Study on Electrical Discharge Machining of Ultra-Fined Grain Al, Cu and Steel”, Journal of Metallurgical and Materials Transactions A, Vol. 47, No. 12, 2016, pp. 6237-6247.

[5]   Rafati E., Mahdieh M. S., and Kargar S., “Optimization of Variance of Roller Burnishing Parameters on Surface Quality by Taguchi Approach”, International Journal of Advanced Design and Manufacturing Technology, Vol. 6, No. 3, 2013, pp. 78-81.

[6]   Naeini, S. E., Spelt, J. K., “Two-Dimensional Discrete Element Modeling of a Spherical Steel Media in a Vibrating Bed”, Powder Technology, Vol. 195, No. 2, 2009, pp. 83-90.

[7]   Mass Finishing URL: http://en.wikipedia.org/wiki/Mass_finishing

[8]   Gillespie, L. K., “Handbook of Mass Finishing”, 1nd ed., Industrial Press Inc., New York, 2007, Chaps. 9, 237. 

[9]       Wang, S., Timsit, R. S., Spelta, J. K., “Experimental Investigation of Vibratory Fnishing of Aluminum”, Wear, Vol. 243, No. 1-2, 2000, pp. 147-156.

[10]    Uhlmann, E., Dethlefs, A., and Eulitz, A., “Investigation into a Geometry-Based Model for Surface Roughness Prediction in Vibratory Finishing Processes”, The International Journal of Advanced Manufacturing Technology, Vol. 75, No. 5, 2014, pp. 815–823.

[11]    Uhlmann,E., Dethlefs, A., and Eulitz, A., “Investigation of Material Removal and Surface Topography Formation in Vibratory Finishing”, Procedia CIRP, Vol. 14, 2014, pp. 25-30.

[12]    Song, X., Chaudhari, R., and Hashimoto, F., “Experimental Investigation of Vibratory Finishing Process”, The American Society of Mechanical Engineering, Vol. 2, No. 4093, 2014, pp. 1-7.

[13]     Behaq, A. M., “Electroforming”, MA Dissertation, Isfahan University Of Technology, Isfahan, Iran, 2011, (In Persian).