Investigation of Mass Magnetic Abrasive Finishing Process on Compressor Blades
محورهای موضوعی : Conventional/Non-Conventional Machining
Seyed Alireza Rasouli
1
(Department of Mechanical Engineering, Malayer University, Malayer, Iran)
Davood Nori
2
(Department of Mechanical Engineering, Malayer University, Malayer, Iran)
کلید واژه: Response Surface Method, Magnetic abrasive finishing, Free Form Surfaces, Compressor Blade, Magnetic Flux Density,
چکیده مقاله :
Attempts at research across various industries to achieve high-quality surfaces have led to the development of new finishing processes. Magnetic Abrasive Finishing is a novel technique where a magnetic field is employed to control an abrasive tool. Gas turbine compressor blades are among the industrial components requiring high surface quality due to their exposed surfaces. The reduction in surface roughness on these components has a significant impact on the efficiency of motor turbines. This paper focuses on studying the Magnetic Abrasive Finishing process parameters for the free surfaces of Titanium blades. Using a mass Magnetic Abrasive Finishing machine, the influence of powder weight, type of abrasive particles, and gap on the variation of surface roughness is investigated through statistical methods such as the response surface. The fabrication of the machine and determination of magnet polarity are carried out using Maxwell simulation software. The Factorial method is employed for experiment configuration. Mechanically alloyed powders produced by ball mills are used in this study. Results demonstrate that employing the magnetic abrasive method can reduce the surface roughness of the blade by up to 33%. The empirical model derived from regression analysis is utilized to predict the variation in surface roughness. Variance analysis of the experimental results indicates the significance of all studied parameters. Scanning Electron Microscopy (SEM) and Atomic Force Microscopy (AFM) are employed for a qualitative evaluation of the results.
Attempts at research across various industries to achieve high-quality surfaces have led to the development of new finishing processes. Magnetic Abrasive Finishing is a novel technique where a magnetic field is employed to control an abrasive tool. Gas turbine compressor blades are among the industrial components requiring high surface quality due to their exposed surfaces. The reduction in surface roughness on these components has a significant impact on the efficiency of motor turbines. This paper focuses on studying the Magnetic Abrasive Finishing process parameters for the free surfaces of Titanium blades. Using a mass Magnetic Abrasive Finishing machine, the influence of powder weight, type of abrasive particles, and gap on the variation of surface roughness is investigated through statistical methods such as the response surface. The fabrication of the machine and determination of magnet polarity are carried out using Maxwell simulation software. The Factorial method is employed for experiment configuration. Mechanically alloyed powders produced by ball mills are used in this study. Results demonstrate that employing the magnetic abrasive method can reduce the surface roughness of the blade by up to 33%. The empirical model derived from regression analysis is utilized to predict the variation in surface roughness. Variance analysis of the experimental results indicates the significance of all studied parameters. Scanning Electron Microscopy (SEM) and Atomic Force Microscopy (AFM) are employed for a qualitative evaluation of the results.
[1] Qian, C., Fan, Z., Tian, Y., Liu, Y., Han, J. and Wang, J. 2021. A review on magnetic abrasive finishing. The International Journal of Advanced Manufacturing Technology. 112(3): 619-634. doi: 10.1007/s00170-020-06363-x.
[2] Barman, A. and Das, M. 2019. Toolpath generation and finishing of bio-titanium alloy using novel polishing tool in MFAF process. The International Journal of Advanced Manufacturing Technology. 100(5):1123-1135. doi: 10.1007/s00170-017-1050-2.
[3] Jiao, A., Zhang, G., Liu, B. and Liu, W. 2020. Study on improving hole quality of 7075 aluminum alloy based on magnetic abrasive finishing. Advances in Mechanical Engineering.12 (6): 1-14. doi: 10.1177/1687814020932006.
[4] Singh, P., Singh, L. and Singh, S. 2020. Analyzing process parameters for finishing of small holes using magnetically assisted abrasive flow machining process. Journal of Bio-and Tribo-Corrosion. 7(1):1-10. doi: 10.1007/s40735-019-0315-8.
[5] Vahdati, M. and Rasouli, S. 2016. Evaluation of parameters affecting magnetic abrasive finishing on concave freeform surface of Al alloy via RSM method. Advances in Materials Science and Engineering. Article ID 5256347. doi: 10.1155/2016/5256347.
[6] Yan, B. H., Chang, G. W., Chang, J. H. and Hsu, R. T. 2004. Improving electrical discharge machined surfaces using magnetic abrasive finishing, Machining science and technology, 8(1): 103-118. doi: 10.1081/MST-120034246.
[7] Girma, B., S. Joshi, S., Raghuram, M. and Balasubramaniam, R. 2006. An experimental analysis of magnetic abrasives finishing of plane surfaces, Machining science and Technology, 10(3): 323-340. doi: 10.1080/10910340600902140.
[8] Lin, C. T., Yang, L.D. and Chow, H. M. 2007. Study of magnetic abrasive finishing in free-form surface operations using the Taguchi method. The International Journal of Advanced Manufacturing Technology. 34(1-2):122-130. doi: 10.1007/s00170-006-0573-8.
[9] Yin, S. and Shinmura, T. 2004. A comparative study: polishing characteristics and its mechanisms of three vibration modes in vibration-assisted magnetic abrasive polishing, International Journal of Machine Tools and Manufacture, 44(4):383-390. doi: 10.1016/j.ijmachtools.2003.10.002.
[10] Kim, Y. J. 2007. Magnetic polishing of three dimensional die and mold surfaces. The International Journal of Advanced Manufacturing Technology, 33(1-2):18-23. doi: 10.1007/s00170-007-1018-8.
[11] Zhang, M. D. and Lv, M. and Chen, H. 2009. Theoretical research on polishing free-form surface with magnetic abrasive finishing. Key Engineering Materials. 392(394):404-408. doi: 10.4028/www.scientific.net/KEM.392-394.404.
[12] Ding, Y. H., Yao, X. G., Wang, X. X. and Yang, S. C. 2008. Study on the performances of the ferromagnetic poles based on the curved surface magnetic abrasive finishing. Key Engineering Materials. 359(360):365-368. doi: 10.4028/www.scientific.net/KEM.359-360.365.
[13] Anzai, M., Yoshida, T. and Nakagawa, T. 1996. Magnetic abrasive automatic polishing of curved surface, focused on experimental equipments and characterization, RIKEN Review. 12:15-16.
[14] Alimirzaloo, V., Alimirzaloo, Biglari, P.R., Sadeghi, M.H. 2013. Numerical and experimental investigation of hot forging process of gas turbine engine compressor blade made of titanium alloy. Aerospace Mechanics. 8(4):23-33.
[15] Alimirzaloo,V., Modanloo, V. Hadavifar, M. 2015. Investigation of the effective parameters on the surface roughness and material removal depth in chemical machining of Ti-6Al-4V alloy. Modares Mechanical Engineering, Proceedings of the Advanced Machining and Machine Tools Conference. 15(13): 410-415. dor: 20.1001.1.10275940.1394.15.13.19.9
[16] A.Y. Jiao. 2015. Study of magnetic abrasive finishing in seal ring groove operation. International journal advanced manufacturing technology. 44(2):1-11. doi: 10.1007/s00170-015-8029-7
[17] Hou, T.H., Su, C.H., Liu, W.L. 2007. Parameters optimization of a nano-particle wet milling process using the Taguchi method response surface method and genetic algorithm. Powder Technology. 173(3):153162. doi: 10.1016/j.powtec.2006.11.019.
[18] Montgomery, D. C. 2008. Design and analysis of experiments. John Wiley & Sons.
