Numerical simulation of heat transfer and pressure drop in fluid flow through conical microchannels

Subject Areas : Journal of Simulation and Analysis of Novel Technologies in Mechanical Engineering

Ali Karegar Barkadehi ¹ , Mojtaba Moravej ² , Hamid Mozafari ^{3 *}

1 - Mechanical Engineering Department, Payame Noor University, Po Box 19395-3697, Tehran, Iran.
2 - Mechanical Engineering Department, Payame Noor University, Po Box 19395-3697, Tehran, Iran.
3 - Mechanical Engineering Department, Payame Noor University, Po Box 19395-3697, Tehran, Iran

Received: 2025-09-16 Accepted : 2025-12-27 Published : 2025-12-23

Keywords: Microchannels, Heat transfer, Pressure drop, Reynolds number, Constant heat flux, Numerical simulation.,

Abstract :

This study presents a numerical investigation of laminar flow and heat transfer in conical microchannels using computational fluid dynamics (CFD). The performance of the microchannel is examined over a range of Reynolds numbers, as well as different inlet, outlet, and total channel lengths. The results show that the pressure drop exhibits a coupled dependence on both inlet length and Reynolds number. Increasing the inlet length leads to an average reduction of 19% in pressure drop for every 1-mm increase, whereas increasing the Reynolds number produces an average increase of 37.5% for every 300-unit increment. The heat-transfer coefficient decreases with increasing inlet length but increases with increasing Reynolds number. On average, a 300-unit rise in Reynolds number leads to a 10.17% increase in the heat-transfer coefficient, while a 1-mm increase in inlet length results in a 52.5% decrease. The temperature difference between the inlet and outlet is found to be primarily governed by the Reynolds number, with negligible sensitivity to inlet length; for every 300-unit increase in Reynolds number, this temperature difference decreases by approximately 25%. The outlet length also influences both pressure drop and heat-transfer coefficient, following similar trends: a 300-unit increase in Reynolds number results in an average increase of 55.73% in pressure drop and 10.32% in heat-transfer coefficient. Overall, the results demonstrate that geometric variations and flow conditions significantly affect the hydrodynamic and thermal behavior of conical microchannels, providing useful insights for the design and optimization of micro-scale thermal systems.

References:


[1] Guo, L., Camm, J., Hirokawa, T., Li, H., Houang, L., (2025). A detailed review on the role of critical heat flux in micro-channel dry out phenomena and strategies for heat transfer enhancement. International Journal of Heat and Mass Transfer, 241, 126740.
[2] Habibi Khalaj, A., Halgamuge, S. K., (2017). A review on efficient thermal management of air- and liquid-cooled data centers: from chip to the cooling system. Applied Energy, 205, 1165-1188.
[3] Zhang, Y., Miao, L., Chen, L., Hou, Y., (2025). Visualization and experimental investigation of two-phase flow in S-shaped microchannel heat sink. International Communications in Heat and Mass Transfer, 164, 108883.
[4] Monavari, A., Jamaati, J., Bahiraei, M., (2021). Thermohydraulic performance of a nanofluid in a microchannel heat sink: Use of different microchannels for change in process intensity. Journal of the Taiwan Institute of Chemical Engineers, 125, 1-14.
[5] Haniyeh, H., Seyed Ali, H., Seyed Abbas Sadat, S., & Ali Rajab, P., (2022). Modeling and Experimental Investigation of the Performance of Different Wide and Narrow Microchannel Geometries in Particle Trapping. Modeling in Engineering, 20(68), 113-125.
[6] Sanei, F., Ali, A. B. M., Jasim, D. J., (2024). Salashour, Numerical simulation of the nanofluid flow and heat transfer in porous microchannels with different flow path arrangements using single-phase and two-phase models. International Journal of Thermofluids, 24, 100846.
[7] John, J. J. & Van Gerven, T., (2022). Effect of ultrasound on parallel flow in a microchannel. Chemical Engineering and Processing: Process Intensification, 171, 108465.
[8] Khan, W., Chandra, A. K., Sachan, S., & Alam, M. S., (2022). Effects of Channel Hydraulic Diameters and Flow Ratios of Two-Phase Flow in Y-Junction Microchannels. Chemical Engineering & Technology, 45(3), 535-542.
[9] Lin, Y., Luo, Y., Li, W., & Minkowycz, W., (2021). Enhancement of flow boiling heat transfer in microchannels ysing micro-fin and micro-cavity surfaces. International Journal of Heat and Mass Transfer, 179, 121739.
[10] Gulati, P., Pannu, A., Kumar, M., (2022). Microneedles based drug delivery systems: an updated review. International Hournal of Health Science, 6(7), 109-242.
[11] Nadda, R., Singh, P. K., Das, D. B., (2024). Revolutionizing microneedle array fabrication using additive manufacturing technologies: Potential applications and clinical translation. Journal of Drug Delivery Science and Technology, 101, 106288.
[12] Anderson, J. D., (2009). Governing Equations of Fluid Dynamics, Springer-Verlag Berlin Heidelberg.
[13] Mangani, L., Alloush, M. M., Lindegger, R., Hanimann, L., (2022). A pressure-based fully-coupled flow algorithm for the control volume finite element method. Applied Science, 12, 4633.
[14] Siadaty, M. & Kazazi, M., (2018). Study of water-based nanofluid flows in annular tubes using numerical simulation and sensitivity analysis. Heat and Mass Transfer, 54(10), 2995-3014.
[15] Wang, Q., Tao, J., cui, Z., Zhang, T., (2024). Numerical simulation of fluid and heat transfer characteristics of microchannel heat sink with fan-shaped grooves and triangular truncated ribs. International Communications in Heat and Mass Transfer, 155, 107580.
[16] Chicone, C., (2017). Reaction, Diffusion, and Convection; Chapter 5. An Invitation to Applied Mathematics, 85-193.
[17] Briclot, A., Henry, J. F., Popa, C. V., Nguyen, C. T., (2021). Experimental investigation of the heat and fluid flow of an Al2O3-waternano fluid in the laminar-turbulent transition region. International Journal of Thermal Sciences, 158, 106546.