A Comparative Study Between Analytical, Finite Element Method andthe Experimental Results in Wire Drawing of Copper

Subject Areas : Journal of Simulation and Analysis of Novel Technologies in Mechanical Engineering

محمد احمدپور ¹ (کارشناس‌ارشد، مدرس دانشکده مهندسی مکانیک، دانشگاه آزاد اسلامی واحد خمینی‌شهر)
حسن خادمی‌زاده ² (استادیار دانشکده مهندسی مکانیک، دانشگاه آزاد اسلامی واحد خمینی‌شهر)

Received: 2015-10-03 Accepted : 2015-10-03 Published : 2008-12-21

Keywords: Finite element method (FEM), Wire Drawing, Drawing Force,

Abstract :

The wire drawing process is extensively used in manufacturing components such as rivet, screw, welding wire, etc. In this work, an analytical of the wire drawing process has been considered for two-stage operation. ABAQUS commercial Finite Element code has been used to obtained the drawing force. Then, The analytical and experimental results been compared. The results show a good agreement for copper.

References:

[1] Mellor P.B., Johnson W., Engineering Plasticity, Van Nostrand Reinhold Company, London, 1972.

[2]  Prager W., Hodge P.G., A New Theory of Plastic Solids, Chapman and Hall, London, 1951.

[3]    Draker D.C., Green berg W., 1951, The safety factor of an elastic-plastic body in plane strain, J. Applied Mechanics, Trans. ASME, Vol. 73, 1951, pp. 371-378.

[4]    Hill J., 1950, Mathematical theory of plasticity,  Oxford University Press, London

[5]    Mac Lellian, G.D.S., Some friction effects in wire drawing, T. Inst-Metal, 1953, Vol. 81, pp.1-13.

[6]    Majors  H.J.R., 1955, Studies in cold drawing,  Trans. ASME, Vol. 78, pp. 79.

[7]    Atkins A.G., Caddell R.M., 1968, The influence of reduction work when drawing rod through conical dies, J. Int. Mesh. Sci., Vol. 10, pp. 15.

[8]  Sawamiphakdi K., Kropp P.K., Lahoti G.D., 1988, Investigation of residual stress in drawn wire by the finite element method, Trans. ASME., Vol. 8, pp. 117-122.

[9]    Mathur K.K., Dawson P.R., 1990, Texture development during wire drawing, J. Eng. Mater Tech. Trans. ASME., Vol. 112, N. 3, pp. 292-297.

[10]   Masao M., Masahiko J., 2001, The utility of radially and ultrasonically vibrated dies the wire drawing process, J. Mater.  Tech. 113, pp. 81-86.

[11]   Hayashi M., Masahiko J., Simulation of ultrasonic-vibration drawing using the finite element method (FEM),  J. Mater.  Tech. Vol. 140, 2003, pp. 30-35.

[12]   Tiernan P., Hillery M.T., Dieless wire drawing an experimental and numerical analysis, J. Mater. Tech. 155-156, 2004, pp. 1178-1183.

[13]    Rubio E.M., Camacho A.M., Calculation of the forward tension in drawing processes, J. Mater. Tech. 162-163, 2005, pp. 551-557.

[14]   Norasethasopon S., Yoshida K., Influences of   
 inclusion shape and size in drawing of copper shaped-wire, J. Mater. Tech.172, 2006, pp. 400-406.

[15]  Bubnovich V.I., Vivancos Calvet J., Gonzalez Rojas H. A., A new analytical solution for prediction of forward tension in the drawing process, J. Material Technology, Vol. 198, 2008,  pp. 93-98.

[16]    Majzoobi G.H., Fereshteh Saniee F.,
 investigations into the effect of redundant shear deformation in bar drawing, J. Mater. Tech. Vol. 201, 2008, pp. 133-137.

[17] تویسرکانی ح.، 1381، شکل‌دهی فلزات، مرکز نشر دانشگاه صنعتی اصفهان، دانشگاه صنعتی اصفهان.

[18] Chakrabarty J., Applied Plasticity, Springer, New York,  2010.