Microstructural Aspects in the Diffusion Bonding of Zr702 to A516 Steel with Ni/Mo/Ti Multi-Interlayer

Subject Areas : Welding

Ali Pourjafar ¹ , Seyed Reza Alavi Zaree ² , Reza Dehmolaei ³ , Khalil Ranjbar ⁴ , Mohammadreza Tavakoli Shoushtari ⁵

1 - Department of material science and engineering,faculty of engineering shahid chamran of ahvaz
2 - Department of Materials Science & Engineering, Faculty of Engineering, Shahid Chamran University of Ahvaz, Ahvaz, Iran.
3 - Department of Materials Science & Engineering, Faculty of Engineering, Shahid Chamran University of Ahvaz, Ahvaz, Iran.
4 - Department of Materials Science & Engineering, Faculty of Engineering, Shahid Chamran University of Ahvaz, Ahvaz, Iran
5 - Department of Materials Science and Engineering, Faculty of Engineering, Shahid Chamran University of Ahvaz, Iran

Received: 2024-08-31 Accepted : 2024-11-03 Published : 2024-12-15

Keywords: diffusion bonding, zirconium 702, multiple interlayers, interface, interdiffusion,

Abstract :

The bonding of zirconium to various grades of steel has found increasing applications in different industries. Due to their fusion welding problems, the solid state bonded joints of these alloys have received more attention from researchers. In this study, diffusion bonding between zirconium alloy Zr702 and low-alloy steel A516 was performed using a multi-layer interlayer consisting of titanium, molybdenum, and nickel. The bonding process was carried out at a temperature range of 900-1050℃ for 30 minutes using the spark plasma diffusion bonding method. The microstructure and interdiffusion of elements at different interfaces were examined using a field emission scanning electron microscope (FESEM) equipped with EDS analysis. The results showed that a suitable bonded joint was successfully established with the interlayers arranged as Zr702/Ti/Mo/Ni/Steel. At the interface of the interlayers with the base metals, no harmful phases, cracks, or discontinuities were observed. In the Zr/Ti joint interface, diffusion zones were identified as (α+β) (Zr,Ti), β(Ti,Zr), and α(Ti,Zr). In the Ti/Mo interface, two solid solution diffusion zones were present, while the Mo/Ni interface showed two areas that included solid solutions and intermetallic phases. In the Ni/A516 joint interface, a solid solution combination and an intermetallic composition were identified. EDS Linear analysis results indicated that the maximum diffusion occurred in the Zr/Ti layer, while the lowest diffusion was observed in the Ti/Mo layer.

References:

[1] B. Zhang, X. Li, T. Wang, and X. Wang, “Microstructure and corrosion behavior of Zr-702 joined by electron beam welding,” Vacuum, vol. 121, 2015.
[2] S. Yang, J. Cai, P. Lv, C. Zhang, W. Huang, and Q. Guan, “Microstructures and properties of zirconium-702 irradiated by high current pulsed electron beam,” Nucl Instrum Methods Phys Res B, vol. 358, 2015.
[3] M. M. Atabaki and A. T. Hanzaei, “Partial transient liquid phase diffusion bonding of Zircaloy-4 to stabilized austenitic stainless steel 321,” Mater Charact, vol. 61, 2010.
[4] A. Lebaili, S. Lebaili, and F. Hodaj, “Interfacial interactions between 304L stainless steel and Zy-4 alloy during isothermal holdings at 1050 °C Interfacial interactions between 304L stainless steel and Zy-4 alloy during isothermal holdings at 1050°C,” °C. Journal of Alloys and Compounds, vol. 805, 2019.
[5] H. Wang et al., “Diffusion bonding of Zr-2.5Nb zirconium alloy and 304L stainless steel with Nb/Ni hybrid interlayer,” Mater Lett, vol. 324, 2022.
[6] M. S. Slobodyan, “Methods of Creation of Permanent Zirconium Alloy Joints in Reactor Art: a,” 2016.
[7] K. Komuro, “Welding of zirconium alloys,” Welding International, vol. 8, 1994.
[8] M. Mazar Atabaki, M. E. Bajgholi, and E. H. Dehkordi, “Partial transient liquid phase diffusion bonding of zirconium alloy (Zr-2.5Nb) to stainless steel 321,” Mater Des, vol. 42, 2012.
[9] X. long Gao, L. kun Li, J. Liu, X. Wang, and H. Yu, “Analysis of Ni interlayer effects on laser beam welding of dissimilar pure Mo alloy to stainless steel,” Int J Refract Metals Hard Mater, vol. 100, 2021.
[10] K. Bhanumurthy, D. Joyson, S. B. Jawale, A. Laik, and G. K. Dey, “Diffusion Bonding of Nuclear Materials”, BARC Newsl, 2013.
[11] S. Habisch, M. Böhme, S. Peter, T. Grund, and P. Mayr, “The effect of interlayer materials on the joint properties of diffusion-bonded aluminium and magnesium,” Metals (Basel), vol. 8, 2018.
[12] V. Srikanth, A. Laik, and G. K. Dey, “Joining of stainless steel 304L with Zircaloy-4 by diffusion bonding technique using Ni and Ti interlayers,” Mater Des, vol. 126, 2017.
[13] S. Zeng, G. You, F. Yao, J. Luo, and X. Tong, “Effect of bonding temperature on the microstructure and mechanical properties of the diffusion-bonded joints of Zr705 alloy,” Materials Science and Engineering: A, vol. 804, 2021.
[14] Z. D. Kadhim, A. I. A.- Azzawi, and S. J. A.- Janabi, “Effect of the Diffusion Bonding Conditions on Joints Strength,” vol. 13, 2009.
[15] M. A. Mofid and E. Loryaei, “Effect of bonding temperature on microstructure and intermetallic compound formation of diffusion bonded magnesium/aluminum joints,” Materwiss Werksttech, vol. 51, 2020.
[16] B. Zhang, C. Chen, J. He, J. Hou, L. Chai, and Y. Lv, “Spark plasma diffusion bonding of TiAl/Ti2AlNb with Ti as interlayer,” Materials, vol. 13, 2020.
[17] Q. Li, G. H. Ma, X. Y. Liu, Z. K. Tu, and D. Pan, “Microstructure and mechanical properties of Ti-Nb-Zr alloys prepared by spark plasma sintering,” in Key Engineering Materials, Trans Tech Publications Ltd, 2017.
[18] W. He, J. Ma, Y. Zhang, H. Wen, and Q. Liu, “Effect of the annealing process on the microstructure and mechanical properties of multilayered Zr/Ti composites,” Materials Science and Engineering: A, vol. 713, 2018.
[19] J. Lin et al., “Novel Ti-Ta-Hf-Zr alloys with promising mechanical properties for prospective stent applications,” Sci Rep, vol. 6, 2016.
[20] K. Bhanumurthy, A. Laik, and G. B. Kale, “Novel Method of Evaluation of Diffusion Coefficients in Ti-Zr System,” Defect and Diffusion Forum, vol. 279, 2008.
[21] A. Cezairliyan and F. Righini, “Thermodynamic studies of the a α -> β phase transformation in zirconium using a sub second pulse heating technique.” Institute for materials research, 1975.
[22] Z. Wang, Y. Guo, L. Ren, G. Quan, Y. Liu, and H. Pan, “Effect of Bonding Temperature on Microstructure and Mechanical Properties of 304L/Zircaloy-4 Diffusion-Bonded Joints with Ni/Ta Hybrid Interlayer,” Adv Eng Mater, vol. 23, 2021.
[23] P. He, J. C. Feng, B. G. Zhang, and Y. Y. Qian, “Microstructure and strength of diffusion-bonded joints of TiAl base alloy to steel.” National Key Laboratory of Advanced Welding Production Technology, Harbin Institute of Technology, 2002.
[24] H. Masumoto, K. Nishio, A. Asada, S. Mukae, M. Katoh, and N. Hatanaka, "Diffusion Bonds between Molybdenum and Titanium." Quar. J. JWS 10, 1992.
[25] K. Bhanumurthy, and R. Rainer. "Diffusion bonding of the Mo-base alloy TZM with interlayers." International journal of materials research 99.7, 2008.
[26] P. Duwez, “Effect of Rate of Cooling on the Alpha-Beta Transformation in Titanium and Titanium-Molybdenum Alloys.” JOM 3,1951.
[27] B. Chen et al., “Investigation of tungsten/MA956 steel diffusion bonding with an Nb/Ni composite interlayer,” Int J Mod Phys B, vol. 34, 2020.
[28] S. Guo and C. T. Liu, “Phase stability in high entropy alloys: Formation of solid-solution phase or amorphous phase,” Progress in Natural Science: Materials International, vol. 21, 2011.
[29] A. Arya, S. Banerjee, G. P. Das, I. Dasgupta, T. Saha-Dasgupta, and A. Mookerjee, “A first-principles thermodynamic approach to ordering in Ni-Mo alloys. Acta materialia, 49, 2001.
[30] C.P. Heijwegen, "Diffusion in the binary systems of molybdenum with nickel, iron and cobalt.", 1973.
[31] J. Zhang, Q. Shen, G. Luo, M. Li, and L. Zhang, “Microstructure and bonding strength of diffusion welding of Mo/Cu joints with Ni interlayer,” Mater Des, vol. 39, 2012.
[32] R. E. W. Casselton, W. Hume-Rothery. "The equilibrium diagram of the system molybdenum-nickel." Journal of the Less Common Metals 7.3, 1964.
[33] K. Yaqoob, J. C. Crivello, and J. M. Joubert, “Thermodynamic modeling of the Mo–Ni system,” CALPHAD, vol. 62, 2018.
[34] H. Sabetghadam, A. Z. Hanzaki, and A. Araee, “Diffusion bonding of 410 stainless steel to copper using a nickel interlayer,” Mater Charact, vol. 61, 2010.
[35] L. J. Swartzendruber, V. P. Itkin, and C. B. Alcock, "The Fe-Ni (iron-nickel) system." Journal of phase equilibria 12, 1991.